Arduino Uno & Shields

Product Details:

Mega +WiFi R3 Atmega2560+NodeMCU ESP8266 32Mb Memory USB-TTL CH340G Compatible For Arduino Mega is Full integration on one board Mega R3 ATmega2560 and WiFi ESP8266 with memory 32Mb.

All of the modules can work together or separately. And everyone has their own pinout headers. The convenient solution for the development of new projects requiring Uno and WiFi. Via USB you can update sketches and firmware for ATmega328 and for ESP8266.

It is a customized version of the classic ARDUINO MEGA R3 board. Full integration of Atmel ATmega2560 microcontroller and ESP8266 Wi-Fi IC, with 32 Mb (megabits) of flash memory, and CH340G USB-TTL converter on a single board! All components can be set up to work together or independently.

For this onboard have the USB-serial converter CH340G. Use this board is very simple. The board has DIP-switch, to connect the modules. For example, to USB and ATmeg2560, USB and ESP8266, ATmega2560 and ESP8266.

Product Details:

• Features: A monolithic integrated, high voltage, high current, 4-channel driver
• Using this chip you can use DC motors and power supplies of up to 36 V, so that some pretty big motors and the chip can supply a maximum current of 600mA per channel Also known as a type of H-Bridge, which is typically an electrical circuit that enables a voltage to be applied across a load in either direction to an output, e.g. motor.

Product Details:

Description -

Richduino is better option for students, trainers, faculties, professors, engineers, industries offer high quality affordable boards for Arduino IDE.
Richduino is inspired from open source Arduino platform specifications.
Low price and highest degree of production quality are two main objectives of Freeduino.

 

Technical specifications-

Microcontroller : Atmega328

Operating Voltage : 5V DC

Input Voltage (via DC Adapter) : 9V DC

Alternate input voltage source : USB connection

Digital I/O pins : 14 (of which 6 can be used as PWM output)

Analog input pins : 6 (with modification in code, these pins act as normal I/O pins)

DC Current Limit for I/O Pins : 40mA

DC Current Limit for 3.3V Pin : 500mA (if input voltage is sourced from DC adapter)

DC Current Limit for 3.3V Pin : 150mA (if input voltage is sourced from USB)

Switching between power sources : Manual Jumper Pin

Program Memory : 32KB onchip memory of ATmega328 (of which 0.5KB is used by bootloader)

SRAM : 2KB onchip memory of ATmega328

EEPROM : 1KB onchip memory of ATmega328

Clock Speed : 16Mhz

Mechanical Pin compatibility : with Arduino UNO R3

Board dimensions: 69mm X 55mm (Board is rectangular)

Mounting holes : Matching with UNO R3

Product Details:

A very useful module that acts as a Minimum System Development Board Module For Arduino . On-board Mini USB interface, you can give the board power supply and USB communication .

Additional Information:

• Item Code: ARMSTM32

Product Details:

Product Description:
The ATtiny85 based mini development board is similar to the Arduino, but cheaper and smaller (of course a bit less powerful). With a whole host of shields to extend its functionality and the ability to use the familiar Arduino IDE, this board is a great way to jump into microcontroller electronics.Product Specs:
Support for the IDE 1.0+ (OSX / Win / Linux)Power via USB or External Source - 5v or 7-35v (automatic selection)On-board 500ma 5V RegulatorBuilt-in USB (and serial debugging)6 I / O Pins (2 are used for USB only if your gram actively communicates over USB, otherwise you can use all 6 even if you are gramming via USB)8k Flash Memory (about 6k after bootloader)I2C and SPI (vis USI)PWM on 3 pins (more possible with Software PWM)ADC on 4 pinsPower LED and Test / Status LED (on Pin0)

Additional Information:

• Item Code: ATTINY85V2

Product Details:

Description -

Richduino is better option for students, trainers, faculties, professors, engineers, industries offer high quality affordable boards for Arduino IDE. 
Richduino is inspired from open source Arduino platform specifications. 
Low price and highest degree of production quality are two main objectives of Freeduino. 

 

Technical specifications-

Microcontroller : Atmega328

Operating Voltage : 5V DC

Input Voltage (via DC Adapter) : 9V DC

Alternate input voltage source : USB connection

Digital I/O pins : 14 (of which 6 can be used as PWM output)

Analog input pins : 6 (with modification in code, these pins act as normal I/O pins)

DC Current Limit for I/O Pins : 40mA

DC Current Limit for 3.3V Pin : 500mA (if input voltage is sourced from DC adapter)

DC Current Limit for 3.3V Pin : 150mA (if input voltage is sourced from USB)

Switching between power sources : Manual Jumper Pin

Program Memory : 32KB onchip memory of ATmega328 (of which 0.5KB is used by bootloader)

SRAM : 2KB onchip memory of ATmega328

EEPROM : 1KB onchip memory of ATmega328

Clock Speed : 16Mhz

Mechanical Pin compatibility : with Arduino UNO R3

Board dimensions: 69mm X 55mm (Board is rectangular)

Mounting holes : Matching with UNO R3

Product Details:

A simple Arduino CNC shield kit (Arduino Extension Board) with the following features:

Latest Arduino CNC Shield Version 3.10
GRBL 0.9 compatible. (Open source firmware that runs on an Arduino UNO that turns G-code commands into stepper signals)
PWM Spindle and direction pins
4-Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13)
2 x End stops for each axis (6 in total)
Coolant enable
Uses removable Pololu A4988 compatible stepper drivers. (A4988, DRV8825 and others) (Not Included)
Jumpers to set the Micro-Stepping for the stepper drivers. (Some drivers like the DRV8825 can do up to 1/32 micro-stepping )
Compact design.
Stepper Motors can be connected with 4 pin molex connectors or soldered in place.
Runs on 12-36V DC. (At the moment only the Pololu DRV8825 drivers can handle up to 36V so please consider the operation voltage when powering the board.)
Please note that this is an unassembled kit and needs soldering.
* * * Jumpers color may vary depending on the available stock.
NOT INCLUDED:

Arduino Uno
1-4 Pololu A4988 compatible stepper drivers

Product Details:

Uno+WiFi R3 AtMega328p+NodeMSU ESP8266 32mb Memory USB-TTL CH340G Compatible for Arduino UNO is full integration on one board: Uno R3 ATmega 328 and WiFi ESP8266 with memory 32Mb (MegaByte). All of the modules can work together or separately. And everyone has their own pinout headers.

The convenient solution for the development of new projects requiring Uno and WiFi. Via USB you can update sketches and firmware for ATmega328 and for ESP8266. For this onboard have the USB-serial converter CH340G.

It is a modernized version of the classic Arduino UNO R3 board. Full integration of a microcontroller ATmega328 and a Wi-Fi chip ESP8266 with 32 MB memory on one board. All modules can work together or individually. Each of the microcontrollers has led to connecting peripheral sensors and modules.

A convenient solution for developing new projects that require Wi-Fi. Through USB, you can update sketches and firmware for both ATmega328 and ESP8266. For this on board, there is a UART converter CH340G. The board has a DIP switch, which switches the modes of interaction of microcontrollers ATmegaa328 and esp8266.

Operations of this board are very simple. The board has DIP-switch, to connect the modules. For example, to USB and ATmega328, USB and ESP8266, ATmega328 and ESP8266.

QUICK OVERVIEW

1. USB-TTL converter.
2. Logic Level: 5V.
3. Operating Supply Voltage: 5V.
4. Digital I/O Pins: 14.
5. Analog I/O Pins: 6.

Product Details:

Product Description:

• Small soldering area.
• All Arduino pins are brought to the top level.
• 1 reset button, 1 general use button, and 2 LED circuits can be used directly.
• 5V, GND, and Raw pins are exposed as well.
• SOIC place for IC.
• The mini breadboard has 170 tie points.
• The breadboard sticks on the prototype shield with its self-adhesive backing.
• Prototype Size:7cm x 5.5cm x 2cm
• Mini breadboard size: 4.4 * 3.4 * 1cm

Additional Information:

• Item Code: PRTPSHLD

Product Details:

Clear Acrylic Box / Enclosure / Case / Shell for Arduino Uno R3 Board Module . Please Note: The UNO R3 module is not included.

Additional Information:

• Item Code: ARCASEFF

Product Details:

This Arduino Uno is an original microcontroller board from Arduino officials based on the ATmega328P.  It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz quartz crystal, a USB connection, a power jack, an ICSP header and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with an AC-to-DC adapter or battery to get started.. You can tinker with your UNO without worrying too much about doing something wrong, worst case scenario you can replace the chip for a few dollars and start over again.“Uno” means one in Italian and was chosen to mark the release of Arduino Software (IDE) 1.0. The Uno board and version 1.0 of Arduino Software (IDE) were the reference versions of Arduino, now evolved to newer releases. The Original Arduino Uno Rev3 board is the first in a series of USB Arduino boards and the reference model for the Arduino platform; for an extensive list of current, past or outdated boards see the Arduino index of boards.1 x Original Arduino Uno Rev3

Product Details:

This is a 16x2 LCD Keypad module for Arduino Diecimila Duemilanove, UNO, MEGA1280, MEGA2560 board.Blue Backlight with white words, adjustable backlighting4 Bit Arduino LCD Library
The LCD Keypad shield is developed for Arduino compatible boards, to provide a user-friendly interface that allows users to go through the menu, make selections etc. It consists of a 1602 white character blue backlight LCD. The keypad consists of 5 keys - select, up, right, down and left. To save the digital IO pins, the keypad interface only uses one ADC channel. The key value is read out through a 5 stage voltage divider.

Product Details:

This is a I/O extension shield for Arduino Nano making connection easier.
Features: • Expansion shield for Arduino Nano• Pin out for 14 digital input/output pins• Pin out for 6 PWM outputs• Pin out for 8 analog inputs• Pin out for I2C Interface• Power jack• Reset button• LED for power indicator• AMS1117 3.3V Output Voltage• Also compatible with Arduino UNO after soldering pin headers to this shield
Size:2.3" x 2.2" x 0.5"

Product Details:

We can build electronics projects just as easy as piling bricks. and community have made the programming much easier than ever before. How about some elixir on hardware part? Maybe it is not yet convenient to make complex interfaces, but we can at least start from the most commonly used modules.   By using electronic bricks, you may connect compatible boards easily with various digital, analog and I2C/Uart interfaces. These the breadboard-less firm connection are prepared to extensive modules like poteniometers, sensors, relays, servos...even buttons, just plug and play.
   Each terminal module has buckled port with VCC, GND and Output, which has corresponding port on the sensing board, with a plain 2.54mm dual-female cable you may start playing already. Buckled brick cables are like cement for bricks, make the connections easier, secure and more professional looking.  You can easily connect with usual analog sensors by using this expansion board, such as ray sensor.If you support by this expansion board and corresponding circuit module,you only need to combine and sensors module by using special cables because concrete circuit details achieve by corresponding sensors module, so you only need to consider that how to read data coming from the sensor by program in .
Product Feature - Emartee Sensor Shield V5.0 pinout all of the digital and analog interface;Support IIC interfaceSupport 32 road Servo Motor Drive Shield interfaceSupport bluetooth module communication interfaceSupport SD card module communication interfaceSupport APC220 wireless rf modules communication interfaceSupport RB URF ultrasonic sensors interfaceSupport LCD serial and parallel interface
Package Includes -    1pcs for Arduino Sensor Shield V5.0 Expansion Development Board

Product Details:

Description:The Mega Pro Embed CH340G / ATmega2560 board is based on the ATmega2560 microcontroller. Built on the Atmel ATmega2560 microcontroller and USB-UART interface chip CH340G. This is a great solution to get your final project on the welding prototype board.The Mega Pro Embed functionalities are identical to the Mega 2560. Even though it is an Embed board, it is solid as stable as the Mega Board. It uses the original chip, and 16 MHz high-quality quartz resonators are present on the board. The board uses the chip CH340G as the converter UART-USB. It provides a stable data exchange result when you work at a frequency of 12Mhz (requires the driver to be installed on the computer).You can power the board or power the pins through the MicroUSB connector. The voltage regulator (LDO) can handle input voltages from 6V to 9V (peak 18V) DC. The voltage regulator allows to use up to 18V as an input value, however, we do not recommend exceeding the recommended values aforementioned, since this can lead to excessive heat and damage the device.________________________________________Features:1. The board is compatible with Mega 2560.2.  excellent solution for developing projects based on ATmega2560.3. The board can be powered directly through the Micro USB connector4. The maximum output current upon 5V is around 800mA, while on the 3.3V it is about 800mA.________________________________________Specifications • Microcontroller ATmega2560• USB-TTL converter: CH340• Power Out:5V-800mA• Power IN.: 5V• Power IN. VIN/DC Jack:5V• Power Consumption: 5V 220mA• Logic Level: 5V• USB: Micro USB• Clock Frequency: 16MHz• Operating Supply Voltage: 5V• Digital I/O: 54• Analog I/O: 16• Memory Size: 256kb• Data RAM Type/Size: 8Kb• Data ROM Type/Size: 4Kb• Interface Type: ISP• Operating temperature −40??°/+85??°• Length x Width :38mm×54mm
Package Includes:1 x Mega2560 Pro ATMEGA2560-16AU USB CH340G Intelligent Electronic Development Board1 x 21 Pin Headers1 x 16 Pin Headers1 x 3 Pin Headers

Product Details:

The 3.5 inch TFT LCD Touch Display Shield for Arduino Uno is fully assembled, tested and ready to go. Add the touch display without wiring, no soldering! Simply plug it in and load up a library – you’ll have it running in under 10 minutes! Works best with any classic Arduino ATMEGA328 BoardSo spice up your Arduino UNO project with a beautiful large touchscreen display shield with a built-in microSD card connection. This TFT display is big (3.5″ diagonal) bright (4 white-LED backlights) and colorful (18-bit 262,000 different shades)!The Display comes with 480×320 pixels with individual pixel control. It has way more resolution than a black and white 128×64 display.  As a bonus, this display has a resistive touchscreen attached to it already, so you can detect finger presses anywhere on the screen.
Features:3.5″ diagonal LCD TFT display, with bright 4 white-LED backlights, default state: onIt can control the backlight to connect the transistor to a digital pin480×320 Pixels, with colorful and 18-bit, 262,000 different kinds of shade4-wire resistive touchscreen8-bit digital interface, plus 4 control lines
Package Includes:1 x 3.5″ inch ILI9486 TFT Touch Shield LCD Module 480×320 for Arduino Uno1 x Stylus