Stepper Motor & Drivers

Product Details:

Nema 17 is the motor of choice for RepRaps/3D printers/ Desktop CNC Routers. It is also a suitable motor for various robotics applications. This motor is the most preferred motor used by the rep rap community. 
Specifications -  
Step Angle : 1.8 deg Step Angle Accuracy : +/- 5% Resistance Accuracy : +/- 10%Inductance Accuracy : +/- 20%Temprature Rise : 80 deg C Max Ambient Temerature : -10 deg C +50 deg C Insulation Resistance : 10 M Ohms Min. , 500VDC Dielectric Strength : 500 VAC for one minuteShaft Radial Play : 0.02 Max (450 g-load) Shaft Axial Play : 0.08 Max (450 g-load)
Specifications : Current A - 1.5Resistance (ohms) - 2.8Inductance (mH) - 5.5Holding Torque N.cm - 55Detent Torque N.cm - 2.6No. of Leads - 4 (bipolar)Weight - 350g Length - 48mm

Product Details:

32-bit DSP control, low noise and superior vibration performance
16 constant torque microstep setting, up to 256 microsteps
Smooth and accurate current control, effectively reduce motor heating
The highest pulse response frequency is 400KHz
When the pulse stops over 200ms, the motor current is halved
Excellent smoothness in low frequency microsteps
Optically isolated differential signal input, strong anti-interference ability
Drive current is adjustable below 6.0A
Voltage input range: AC18~80V
With over voltage, under voltage etc. fault protection
Small size, volume 151*94*54 (mm³), weight 0.65kg
Suitable for 57-86mm(NEMA23-34) 2 phase open-loop stepper motors.
Compared with the standard version, enhanced version adds the
following 6 functions: Pulse smoothing, MF function selection, pulse
filter, polarity selection, pulse mode, self-test pulse 5HKz

Typical Application:
Mainly used in engraving machines, laser equipment, labeling machines, electronic equipment, advertising 

Product Details:

l  32-bit DSP control, low noise and superior vibration performance

l  16 constant torque microstep setting, up to 200 microsteps

l  Smooth and accurate current control, High-speed output increased by 7%, effectively reduce motor heating

l  The highest pulse response frequency is 200KHZ

l  When the pulse stops over 250ms, the motor current is halved

l  Differential signal input, compatible with 5V/24V signals.

l  New single-double pulse function, single/double pulse function switching through shorting or disconnecting the internal terminals of the drive

l Optically isolated differential signal input, strong anti-interference ability

l Drive current is adjustable below 4.0A

l Voltage input range: DC20~50V

l With over voltage, under voltage etc. fault protection

l Small size, volume 118*76*33 (mm³), weight 0.3kg

l Suitable for 42/57/86mm(NEMA17/23/34) 2 phase open-loop stepper motors.

 

 

Typical Application:
Mainly used in medical equipment, dispensing machines, engraving machine, laser equipment, labeling machines, electronic equipment, advertising equipment and other automation equipments. Works particularly good in the expectations of low heat, small noise

Product Details:

l  32-bit DSP control, low noise and superior vibration performance

l  16 constant torque microstep setting, up to 200 microsteps

l  Smooth and accurate current control, High-speed output increased by 7%, effectively reduce motor heating

l  The highest pulse response frequency is 200KHZ

l  When the pulse stops over 250ms, the motor current is halved

l  Excellent smoothness in low frequency high microstep applications

l  Optically isolated differential signal input, strong anti-interference ability

l  Driver current is adjustable below 3.0A

l  Voltage input range: DC20~50V

l  With over voltage, under voltage etc. fault protection

l  Small size, volume 118*76*24.2 (mm³), weight 0.3kg

l Suitable for 42~86mm(NEMA17~34) 2 phase open-loop stepper motors.

Product Details:

General Specification: 
Current / Phase: 1.5A. Step Angle(degrees): 1.8. Phase: 2.  Type: Hybrid. Certification: ROHS,CE. Holding Torque: 4.2 KGCM.  Step angle accuracy: + - 5%(full step,not load). Resistance accuracy: + - 10%. Inductance accuracy: + - 20%. Temperature rise: 80deg Max(rated current,2 phase on). Ambient temperature ----------20deg ~+50deg. Insulation resistance:100M Min,500VDC. Insultion Strength--------500VAC for one minute. 
(Lead Screw): Lead Screw Material: 304 Stainless Steel. Color:Sliver. Diameter: 8mm. Length: 300mm. Lead of thread: 8mm. 
Package Included: 
1x 17HS4401 Stepper Motor. 1x 300mm Lead Screw. 1x T8 Nut.

Product Details:

The DMA860HH is a high performance microstepping driver based on pure-sinusoidal currentcontrol technology. Owing to the above technology and the self-adjustment technology (self-adjustcurrent control parameters) according to different motors, the driven motors can run with smallernoise, lower heating, smoother movement and have better performances at higher speed than mostof the drivers in the markets. It is suitable for driving 2-phase and 4-phase hybrid stepping motors.

Features
l High performance, cost-effective
l Supply voltage up to 80VAC or +110VDCl Output current up to 7.2A
l Self-adjustment technologyl Pure-sinusoidal current control technology
l Pulse input frequency up to 300 KHzl TTL compatible and optically isolated input
l Automatic idle-current reduction
l 16 selectable resolutions in decimal andbinary, up to 51,200 steps/rev
l Suitable for 2-phase and 4-phase motorsl Support PUL/DIR and CW/CCWmodes
l Short-voltage, over-voltage, over-currentand short-cicuit protection

Additional Information:

• Item Code: LSDMA860H

Product Details:

Specifications -
Rated Voltage (V) - 6.6Current/ phase (A) - 1Resistance/ phase (ohms) - 6.6Inductance/ phase (mH) - 8.2Holding Torque (kg-cm) - 7.2No. of Leads - 6Rotor Inertia - 275Weight (kg) - 0.65Detent Torque (kg-cm) - 0.36Length (mm) - 51Step Angle - 1.8°Step Angle Accuracy - ±5% (full step, no load)Resistance Accuracy - ±10%Inductance Accuracy - ±20%Frame Size (mm) - 57x57Shaft Length (mm) - 20.6Shaft Diameter (mm) - 6.35Length (mm) - 51Weight (kg) - 0.65

Additional Information:

• Item Code: NEMA24S72

Product Details:

MACH3 Interface Board CNC 5 Axis with Optocoupler latest upgrade 5 axis breakout board is specially designed for the CNC single axis 2-phase stepper driver controller, such as TB6560, M542, M542H, MA860H, 2M542, 2M982, DM542(A), DM860(A) etc. single axis stepper driver controller series. With this 5 axis breakout board, any 1-5 single axis stepper driver controllers can be directly controlled by the PC via the MACH3, EMC2, KCAM4, etc

Features :

1. Maximum support 5-axis stepper motor driver controllers
2. Compatible with MACH3, Linux CNC (EMC2) etc. parallel-control CNC software.
3. USB power supply and peripherals power phase are separate to protect computer security.
4. All the signals are to-isolate which can protect your computer security.
5. 5-input interface to define the Limit, Emergence-Stop, Cutter alignment, etc.
6. Wide input voltage range: 12-24V, and with anti-reverse function.
7. One relay output control interface, accessed by the spindle motor or the air pump, water pump, etc.
8. Output 0-10V analog voltage for the inverter to control the spindle speed.
9. All the way to the relay output port, control spindle switch. Output port P17 mouth.
10. Open all 17 ports, which can be accessed with the optocoupler drive, 5-axis stepper motor can be controlled.
11. Pin P1 as PWM outputs can be controlled with optocoupler input spindle governor.
12. Can be accessed by a common cathode or common anode input level to 5V drive.
13. All the way through the optocoupler isolated 0-10V analog voltage output can be controlled with the corresponding analog interface converter to control the spindle speed. Output port P1 port.

Additional Information:

• Item Code: MACH3BRD

Product Details:

TB6600 stepper motor Driver Controller 4A 9~42V TTL 16 Micro-Step CNC 1 Axis NEW upgraded version of the 42/57/86 stepper motor .

Package includes:

1pcs TB6600 4-aixs stepper motor driver

Detailed Description

This drive is an upgraded version of TB6600, segment increased to 32 segments, suitable for high subdivision applications . Suitable for step motor:57, 42, 86Type 4 phase 2 phase (4 line 6 line 8)
1. 9V-42V DC power supply .
2. H bridge bipolar constant current drive .
3. the biggest4.0AEight kinds of output current are optional .
4. the biggest32To subdivide6 kinds of subdivision modes selectable .
5. input signal high speed photoelectric isolation .
6. a total of standard single pulse interface .
7. offline retention function .
8. semi enclosed casing can adapt to more stringent environment .
9. provide energy saving half automatic current lock function .

Additional Information:

• Item Code: TB6600

Product Details:

Specifications - 
Rated Voltage (V) - 4.2Current/ phase (A) - 4Holding Torque (kg-cm) - 68No. of Leads - 4Length (mm) - 95Step Angle - 1.8°Step Angle Accuracy - ±5% (full step, no load)Resistance Accuracy - ±10%Inductance Accuracy - ±20%Frame Size (mm) - 85x85Shaft Length (mm) - 32Shaft Diameter (mm) – 12

Product Details:

Specifications – 
Rated Voltage (V) - 3.2Current/ phase (A) - 2.8Resistance/ phase (ohms) - 1.13Inductance/ phase (mH) - 3.6Holding Torque (kg-cm) - 18.9No. of Leads - 4Rotor Inertia - 480Weight (kg) - 1Detent Torque (kg-cm) - 0.68Length (mm) - 76Step Angle - 1.8°Step Angle Accuracy - ±5% (full step, no load)Resistance Accuracy - ±10%Inductance Accuracy - ±20%Frame Size (mm) - 57x57Shaft Length (mm) - 20.6Shaft Diameter (mm) - 6.35Length (mm) - 76Weight (kg) – 1

Additional Information:

• Item Code: NEMA24S185

Product Details:

Specifications – 
Rated Voltage (V) - 4.2Current/ phase (A) - 3Inductance/ ph. mH - 3.6Resistance/ phase (ohms) - 1.4Holding Torque (kg-cm) - 34No. of Leads - 4Weight (kg) - 1.7Length (mm) - 66Step Angle - 1.8°Step Angle Accuracy - ±5% (full step, no load)Resistance Accuracy - ±10%Inductance Accuracy - ±20%Frame Size (mm) - 85x85Shaft Length (mm) - 32Shaft Diameter (mm) - 12Length (mm) – 66

Additional Information:

• Item Code: NEMA34S310

Product Details:

Step Angle – 1.8 deg
Voltage/Phase – 4v
Current/Phase – 0.95A
Resistance/Phase – 4.2ohms
Inductance/Phase – 2.5mH
Holding Torque – 16 N.cm
No. of Leads – 6
Rotor Inertia – 35 g.cm2
Weight – 0.22 kg
Length – 33mm
Step Angle Accuracy – (+-) 5%
Resistance Accuracy – (+-) 10%
Inductance Accuracy – (+-) 20%

Product Details:

Specifications -
Rated Voltage (V) - 6.6Current/ phase (A) - 1Resistance/ phase (ohms) - 6.6Inductance/ phase (mH) - 8.2Holding Torque (kg-cm) - 7.2No. of Leads - 6Rotor Inertia - 275Weight (kg) - 0.65Detent Torque (kg-cm) - 0.36Length (mm) - 51Step Angle - 1.8°Step Angle Accuracy - ±5% (full step, no load)Resistance Accuracy - ±10%Inductance Accuracy - ±20%Frame Size (mm) - 57x57Shaft Length (mm) - 20.6Shaft Diameter (mm) - 6.35Length (mm) - 51Weight (kg) - 0.65

Product Details:

Angle Accuracy - ±5% (full step, no load)Resistance - 0.68 ±10%Inductance - 9 ±20%

Additional Information:

• Item Code: NEMA34122KG

Product Details:

Specifications - Phase - 2 phase Bipolar. Step Angle - 1.8 deg. Voltage - 4.8V. Current - 3 A. Resistance - 1.6 Ohms (10% variance).  Inductance - 7.5 mH (20% variance). Holding Torque - 28 kgcm. Insulation Class - B. Mass - 1.5 kg. 

Product Details:

This is essentially a ramped up version of our Ardumoto motor driver shield. For this Monster Moto Shield we’ve replaced the L298 H-bridge with a pair of VNH2SP30 full-bridge motor drivers. We’ve also beefed up the support circuitry so this board is capable of driving a pair of high-current motors! The VIN and motor out are pitched for our 5mm screw terminals (not included), making it easy to connect larger gauge wires.
Note: When using this board in extreme high-demand applications it may be necessary to improve thermal performance with a heat-sink or fan and to solder the wires directly to the board instead of using a screw terminal (in addition to the myriad other complications present in a high-current system) However, when using the board at currents up to 6A the chips will barely become noticeably warm.
Voltage max: 16VMaximum current rating: 30 APractical Continuous Current: 14 ACurrent sensing available to Arduino analog pinMOSFET on-resistance: 19 mΩ (per leg)Maximum PWM frequency: 20 kHzThermal ShutdownUndervoltage and Overvoltage shutdown

Product Details:

This Stepper Motor Controller Board is based on the TOSHIBA 2SC5200. This board can be used to generate PWM signals for the stepper motor driver, it has onboard buttons for the CW and CCW rotation of the stepper motor. The speed of the motor can be varied through the onboard potentiometer.When the board generates a frequency pulse signal, the high and low-frequency signal can be selected by the onboard jumperNote:1. If you want to use the start or stop function, the ENA enable terminal on the controller must be connected to the driver with a common cathode or a common anode.2. The forward and reverse rotation and the start and stop of the motor can be controlled by pressing the button.3. The speed of the motor can be controlled by adjusting the potentiometer to change the frequency.4. The switch of the motor’s forward / reverse rotation and start/stop is an ordinary switch with self-locking.5. If you want to connect the switches that control forward and reverse, and open or stop, to the chassis panel, you can refer to the following instructions.???Change the forward and reverse, the start-stop button into a lead-wire switch, see the pin position on the back:Features:1. It has three frequency ranges selectable via onboard jumpers.2. Frequency can be measured via PUL and common cathode (GND) ports.3. The board has two sets of power inputSpecification:
Power supply: DC15-80V or DC 12VHigh frequency: 5.8KHZ-127KHZMiddle frequency: 590HZ-15.8KHZLow frequency: 82HZ-2.3KHZMeasuring frequency interface: PUL, GND
Package Includes:1 x Stepper Motor Drive Simple Controller Speed Forward and Reverse Control Pulse Generation PWM Generation Controller

Product Details:

Motor Specifications - 
Number of Phase - 2Step Angle - 1.8 degRated Voltage - 1.68V Rated Current - 4.2A Phase Resistance - 0.4 ohm Phase Inductance - 1.5 mH (1kHz 1V RMS) Holding Torque - 12 kg.cm Weight - 0.68kg Insulation Class - B (130) 80K Max Motor with 1000 ppr encoder

20V ~ 50VDC 0.1A - 10A NEMA23 Closed Loop Stepper Motor Driver JK-HSD57
Features of closed loop stepper motor
 Step and direction control Closed position loop for no loss of movement synchronization Operating voltage: 20-50 VDC Load based output current of 0.1 - 10 A High torque at starting and low speed No torque reservation High stiffness at standstill Significantly reduced motor heating Smooth motor movement and extra low motor noise Quick response, no delay and zero settling time No loss of steps; no hunting; no overshooting Plug-and-play and no tuningDescriptions of NEMA23 stepper driver
JK-HSD57 is one of the models in Jkongmotor series easy servo drives which can take 20-50 VDC operating voltage and output 0.1 -10A continuous load-based current. It is capable of driving NEMA 17, 23, 24 and 34 easy servomotors (stepper motors with encoders) with the position loop closed in real time.Based on latest DSP technology and adopting Novo's advanced control algorithm, JK-HSD57 easy servo drive applies servo control on easy servo motors. When adopted with an easy servo motor, it combines features of both open loop steppers & brushless servo systems, and offers many unique advances features for excellent motion control system performance.When an JK-HSD57 easy servo drive is implemented with a novo SC series easy servo motor, there is No Configuration Needed for almost all applications. The output resolution from JK-HSD57 with the output resolution defaulted to output resolution of 2,000 pulses per resolution (equal to 10 microstep in 2-phase stepper systems). Via DIP switches, a user can also easily change the output resolution to one of 15 output resolutions 400 to 51,200 (equal to 2-256 microstep in 2-phase stepper systems). With novo configuration software, ProTuner, an advanced user can also set custom settings of resolution, current & position loop parameters, idle current percentage, etc. Applications - 
With many unique advanced features, JK-HSD57 easy servo systems are ideal for many industries to upgrade stepper performance or replace brushless servo systems in many applications.
Jkongmotor OEM clients have successfully implemented JK-HSD57 driven easy servo systems in applications such as small-to-large size CNC routers, CNC mills, plasmas, large-scale laser cutters / engravers, labeling equipments,robotics, gemstone processing machines, pick & place machines, X-Y tables.
Electrical Specifications - Input Voltage - 20 to 50 VDC Output Current - 0.1 to 10A (Max) Pulse Input Frequency - 0 - 200 kHz Logic Signal Current - 7 - 16 mA Isolation Resistance - 500 M ohm

Product Details:

Product Details:

Product Details:

Product Details:

Product Details:

Product Details:

Product Details:

Product Details:

Product Details:

Product Details:

Product Details:

Product Details:

Product Details:

Product Details:

Product Details:

Product Details:

XB Flexible coupling is commonly used in 3D Printers, CNC machines and other DIY projects to couple Stepper motors and 8MM rods / threaded rods / precision trapezoidal rods. The coupler takes care of small misalignments, deviations and twists in the system. 

Type: XB clamping type

Material: Aluminium alloy

Sleeve Material: Polyurethane

Available in types - 
1) 8mm to 8mm Coupling (NEMA 23)
2) 8mm to 9.5mm Coupling (NEMA 23)
3) 6.35mm to 8mm Coupling (NEMA 23)
4) 12.7mm to 12.7mm Coupling (NEMA 34)
5) 12.7mm to 8mm Coupling (NEMA 34)

Product Details:

Aluminium Helical Shaft coupling is commonly used in 3D Printers, CNC machines and other DIY projects to couple Stepper motors and 8MM rods / threaded rods / precision trapezoidal rods. The coupler takes care of small misalignments, deviations and twists in the system. Our coupling comes with 4 grub screws installed. 

Available in below Variants - 
1) 5mm to 5mm (NEMA 17) 
2) 5mm to 8mm (NEMA 17) 
3) 5mm to 6.35mm (NEMA 17) 
4) 6.35 to 8mm (NEMA 23)

Additional Information:

• Item Code: FLXCPL

Product Details: