Sensor - Load & Flow

Product Details:

This module uses 24 high precision A/D converter chip hx711. It is a specially designed for the high precision electronic scale design, with two analog input channel, the internal integration of 128 times the programmable gain amplifier. The input circuit can be configured to provide a bridge type pressure bridge (such as pressure, weighing sensor mode), is of high precision, low cost is an ideal sampling front-end module.
Features:
Two selectable differential input channelsOn-chip active low noise PGA with selectable gain of 32, 64 and 128On-chip power supply regulator for load-cell and ADC analog power supplyOn-chip oscillator requiring no external component with optional external crystalOn-chip power-on-resetSimple digital control and serial interface: pin-driven controls, no programming neededSelectable 10SPS or 80SPS output data rateSimultaneous 50 and 60Hz supply rejectionCurrent consumption including on-chip analog power supply regulator: normal operation < 1.5mA, power down <1uAOperation supply voltage range: 2.6 ~ 5.5VSize:40mmx20mm/1.56″x0.79″(inch) (approx)Application
Widely used in aerospace, mechanical, electrical, chemical, construction, medicine and many other fields, used to measure force, pressure, displacement, strain, torque, acceleration.

Product Details:

Specification : Model : SEN-HZG1WA. Use voltage : DC 5V. Connect way : G1”,60*34*34(mm). Working voltage range : DC 4.5 ~18V. Max. Working current : 15mA. Test range : 4~45L/min(m³/h). Fit media : water. Working pressure : 1.75MPa. Outside nominal diameter : G1(mm). Instantaneous flow pulse characteristics : F=[5Q-3]±10%, F means instantaneous pulse value(Hz),Q means instant flow(L/min). Insulation resistance ≥ 100MΩ. Electric strength : AC 500V, 50Hz. Precision grade : +-10%. Working temperature : 60 Type : vane-wheel type flowmeter. 
Features : This is a small zise product that easy to install. Made of good quality material, the product is precise and durable, no power consumption. Suitable for gas water heater, electric water heater, washer, wall-hanging stove, electromagnetic water heater, intelligent IC water meter,cooling system, circulatory system, heating equipment,etc. Three lines: red is positive, black is negative, yellow is pulse signal.

Product Details:

Description:-
This DC 24V KK-P50/30 60KG Lifting Solenoid Electromagnet consists of an iron core and a coil to attract magnetic substances, using the magnetic action induced by electric current, only while the current is applied. This compact functional device offers high power with high reliability. The structure and design to release the residual magnetism left after de-energization is also one of its unique features.
Features:
1. Our DC-powered electromagnet generates a magnetic field of high-power with high efficiency.
This highly efficient electromagnet generates a magnetic field of a strong pull (high attractive force) with low energy consumption. You can adjust to the desired attractive force by changing the power applied and the magnetic gap between the electromagnet and the substance.
2. Minimized in residual magnetic.
When an electromagnet is energized, the problem is how to release the magnetic force which remains on the device after the power is turned off. Our electromagnet is designed with measures to release and minimize this residual magnetic force.
3. Lightweight, compact design for space-saving.
Compact mechanism with high reliability.
4. Long life
High mechanical strength and excellent durability.
5. Widely applied in automation: assembly line, sorting machine, mechanical arm, experimental facility, etc

Specification :-
Model: P50/30 60KG
Holding/ Suction Force (KG): 60
Operating Voltage (VDC): 24
Max. Operating Current (mA): 670
Power Consumption (Watt): 15
Operating Temperature Range (°C): -40 to 130
Cable Length (cm): 30
Bolt Size: M6
Body Material: Mild Steel
Dimensions in mm (LxWxH): 50 x 30 (Dia. x Length)
Weight (gm): 346
Shipment Weight: 0.4 kg
Shipment Dimensions: 6 × 5 × 4 cm

Product Includes:-
1 x DC 24V KK-P50/30 60KG Lifting Solenoid Electromagnet
1 x M6 Bolt with Washer

Product Details:

Description:-
This DC 12V KK-P30/25 15KG Lifting Solenoid Electromagnet consists of an iron core and a coil to attract magnetic substances, using the magnetic action induced by electric current, only while the current is applied. This compact functional device offers high power with high reliability. The structure and design to release the residual magnetism left after de-energization is also one of its unique features.
  Features:
1. Our DC-powered electromagnet generates a magnetic field of high-power with high efficiency.
This highly efficient electromagnet generates a magnetic field of a strong pull (high attractive force) with low energy consumption. You can adjust to the desired attractive force by changing the power applied and the magnetic gap between the electromagnet and the substance.
2. Minimized in residual magnetic.
When an electromagnet is energized, the problem is how to release the magnetic force which remains on the device after the power is turned off. Our electromagnet is designed with measures to release and minimize this residual magnetic force.
3. Lightweight, compact design for space-saving.
Compact mechanism with high reliability.
4. Long life
High mechanical strength and excellent durability.
5. Widely applied in automation: assembly line, sorting machine, mechanical arm, experimental facility, etc

Specification :-
Model: DC 12V KK-P30/25
Holding/ Suction Force (KG): 15
Operating Voltage (VDC): 12
Max. Operating Current (mA): 300
Power Consumption (Watt): 3
Operating Temperature Range (°C): -20 to 120
Cable Length (cm): 28
Bolt Size: M4
Body Material: Mild Steel
Dimensions in mm (LxWxH): 30 x 25 (Dia. x Length)
Weight (gm): 98
Shipment Weight: 0.1 kg
Shipment Dimensions: 8 × 5 × 4 cm

Product Includes:-
1 x DC 12V KK-P30/25 15KG Lifting Solenoid Electromagnet
1 x M4 Bolt with Washer

Product Details:

Description:-<br> This DC 24V KK-P40/20 30KG Lifting Solenoid Electromagnet consists of an iron core and a coil to attract magnetic substances, using the magnetic action induced by electric current, only while the current is applied. This compact functional device offers high power with high reliability. The structure and design to release the residual magnetism left after de-energization is also one of its unique features. <br> <br> Features: <br> 1. Our DC-powered electromagnet generates a magnetic field of high-power with high efficiency. <br> This highly efficient electromagnet generates a magnetic field of a strong pull (high attractive force) with low energy consumption. You can adjust to the desired attractive force by changing the power applied and the magnetic gap between the electromagnet and the substance. <br> 2. Minimized in residual magnetic. <br> When an electromagnet is energized, the problem is how to release the magnetic force which remains on the device after the power is turned off. Our electromagnet is designed with measures to release and minimize this residual magnetic force. <br> 3. Lightweight, compact design for space-saving. <br> Compact mechanism with high reliability. <br> 4. Long life<br> High mechanical strength and excellent durability. <br> 5. Widely applied in automation: assembly line, sorting machine, mechanical arm, experimental facility, etc<br><br> Specification :- <br> Holding/ Suction Force (KG): 30<br> Operating Voltage (VDC): 24<br> Max. Operating Current (mA): 340<br> Power Consumption (Watt): 7.5<br> Operating Temperature Range (°C): -25 to 105<br> Cable Length (cm): 30<br> Bolt Size: M5<br> Body Material: Mild Steel<br> Dimensions in mm (LxWxH): 40 x 20<br> Weight (gm): 140<br> Shipment Weight: 0.15 kg<br> Shipment Dimensions: 6 × 5 × 3 cm<br><br> Product Includes:- <br> 1 x DC 24V P40/20 30KG Lifting Solenoid Electromagnet<br> 1 x M6 Bolt with Washer

Product Details:

50Kg Pressure Micro Scale Weighing Sensor Resistance Strain Half Bridge Sensor Body Load Cell
FeatureWhen measuring, the correct force is applied to the outer side of the strain E-shaped beam portion of the sensor (i.e., a strain gauge affixed to the middle, with a beam of white plastic cover arm) and the outside edges to form a shear force in the opposite direction, i.e., in the middle of strain beam bending necessary changes can occur under stress, strain beam side by another force can not have a barrier. The sensor use the following three methods:1. Using a sensor with external resistors full bridge measurement range of a sensor range: 50kg. Higher requirements for external resistor2. The use of only two full-bridge sensors measuring range is the range of the two sensors and: 50kgx2 = 100kg3. The use of four full-bridge sensors measuring range is the range of four sensors and: 50kgx4 = 200kgSize: 34mm x 34mmModel: Weighing Sensor Strain Of Half-bridge Sensor

Product Details:

Function: For the sense of the water flow rate on the following equipments: Thermostatic water heater, water purifier, water dispenser, smart card equipment, coffee machine etc.Calculation Formula :f=(0.2*Q)   Q=L/Min
Note:1. When magnetic material is close with the sensor, its characteristics may vary.2. In order to avoid particle debris, the sensor must be installed after a filter.3. The flow sensor installation has to avoid strong vibration and shaking of the environment, so as not to affect the sensor's measurement accuracy.
Features:
1.  Food grade POM (polyformaldehyde) material, environmental friendly material, small, flexible and functional.2.  Intubation design of inlet and outlet pipe, easy connection and operation;3.  Imported Hall IC from Japan, stable and reliable;4.  Range: 5-150L/min;5.  working voltage: DC4.5-12V;6.  rated voltage: DC5V;7.  Output voltage(rated: DC 5V); High level 4.5V and above; low level 0.5V and below8.  Pulse output duty cycle: 50+-10%9.   Insulation resistance: 100M Ohm and above;10. Tightness: Seal up all the holes, and inflate with 0.8MPa water, after 1 minute, no leakage and deformation;11.  -20-80 centigrade;12.  Hydrostatic pressure: <= 1.75MPa meet Package List: 1 x DN40 flow sensor

Product Details:

Description:Water flow sensor can be used to measure the flow of liquids, i.e. the consumption of liquids in industrial or domestic usage. For example you can make a robotic cocktail dispensing machine, and can use this sensors to accurately measure components like Soda, Water, etc. Water flow sensor consists of a plastic valve body, a water rotor, and a hall-effect sensor. When water flows through the rotor, rotor rolls. Its speed changes with different rate of flow. The hall-effect sensor outputs the corresponding pulse Signal.
I believe using this should be simple, you just need to connect to Arduino interrupt pin 2, and can measure the number of PWM pulse/interrupt per unit of time. The water flow would be directly proportional to the number of measured pulses.
Connection details:
Red wire is +5VBlack wire is GNDWhite wire is PWM signal output 
Description:
Lowest rated working voltage: DC4.5 5V-24VMaximum operating current: 15 mA (DC: 5V)Working voltage range: DC 5~18VLoad capacity: ≤ 10 mA (DC 5V)Temperature: ≤ 80  Operating humidity range: 35%~90%RH (no frost)Allowed pressure: pressure 1.75MpaTemperature: -25~+80 °CExternal threads: 1/2"

Product Details:

Description
The full-bridge structure, the four leads, easy to use, plus driving voltage 5-10V, force changes in the output voltage signal directly.
Wiring: red voltage + E, black line voltage -E, green line signals + S, the white line signal -SThe sensor is fixed at one end through the screw hole, and the other end left floating state, applied according to label directions direction of gravity. In particular, note that you must not directly push the white plastic cover part, in order to avoid damage of the sensor.

Specification:
Hysteresis: 0.0% F.S
Repeatability: 0.05% F.S
Creep (5 minutes): 0.05% F.S
Temperature Effect on Output: 0.003% F.S /°C
Zero output: ± 0.2 mV / V
Input impedance: 1050 ± 10% Ω
Output impedance: 1000 ± 10% Ω
Insulation resistance: ≥2000 MΩ
Operating temperature range: -21 ~ 40°C
Recommended for: kitchen scales
Weight:21g

Additional Information:

• Item Code: LDCL005KG

Product Details:

This DC 12V KK-P25/20 5KG Lifting Solenoid Electromagnet consists of an iron core and a coil to attract magnetic substances, using the magnetic action induced by electric current, only while the current is applied. This compact functional device offers high power with high reliability. The structure and design to release the residual magnetism left after de-energization is also one of its unique features.
Working Principle:An electromagnet is simply a coil of wire.  It is usually wound around an iron core.  However, it could be wound around an air core, in which case it is called a solenoid.  When connected to a DC voltage or current source, the electromagnet becomes energized, creating a magnetic field just like a permanent magnet.   The magnetic flux density is proportional to the magnitude of the current flowing in the wire of the electromagnet.
The polarity of the electromagnet is determined by the direction of the current.  The north pole of the electromagnet is determined by using your right hand.  Wrap your fingers around the coil in the same direction as the current is flowing (conventional current flows from + to -).  The direction your thumb is pointing in the direction of the magnetic field so north would come out of the electromagnet in the direction of your thumb.  DC electromagnets are principally used to pick up or hold objects
We supply many varieties of electromagnets with a higher power as well as lower, original dimensions, etc to satisfy your unique requirements. 
OVERVIEW - Operating Voltage: 12V DC. Lifting Capacity: 5KG. Size (D x L): 25 x 20 mm. Electric lifting magnet. Powerful and compact. Smooth and flat surface. Low consumption and reliable. Ambient temperature within 130 degrees. 
Features:1. Our DC-powered electromagnet generates a magnetic field of high-power with high efficiency. This highly efficient electromagnet generates a magnetic field of a strong pull (high attractive force) with low energy consumption. You can adjust to the desired attractive force by changing the power applied and the magnetic gap between the electromagnet and the substance. 
2. Minimized in residual magnetic - When an electromagnet is energized, the problem is how to release the magnetic force which remains on the device after the power is turned off. Our electromagnet is designed with measures to release and minimize this residual magnetic force. 
3. Lightweight, compact design for space-saving. Compact mechanism with high reliability. 
4. Long life - High mechanical strength and excellent durability. 
5. Widely applied in automation: assembly line, sorting machine, mechanical arm, experimental facility, etc.