Sensor - Temperature And Humidity

Product Details:

Features:Auto Switch the modes between cool and heat;Control temperature by setting the temperature setting value and the difference value;Temperature calibration;Refrigerating control output delay protection;Alarm when temperature exceeds temperature limit or when sensor error.Dimensions:Front panel size: 75(L)×34.5(W)mm;Mounting size :71(L)×29(W)mm;Product size: 75(L)×34.5(W)×85(D)mm;Sensor Cable length: 2m in allSpecifications:Temperature measuring range: -50~99 Resolution: 0.1 Accuracy: ±1 (-50~70 Sensor error delay: 1 minutePower supply: 110VAC±10%, 50/60HzPower consumption: ≤3W;Sensor: NTC sensor (1PC);Relay contact capacity: Cool 10A/250VAC;Heat 10A/250VAC;Ambient temperature: 0~60 Storage temperature: -30~75 Relative humidity: 20%~85% (No condensate).
Packaged included:1x Mini Digital Temperature Controller Thermostat Aquarium1x Temperature sensor probe with 2M cable1x Instruction Manual

Product Details:

Description:1.Type:AM2302 2.Accuracy resolution:0.1 3.Humidity range:0-100%RH 4.Temperature range:-40~80? 5.Humidity measurement precision:±2%RH 6.Temperature measurement precision:±0.5? 7.4-pin package 8.ultra-low power 9.No additional components 10.excellent long-term stability 11.All calibration, digital output 12.completely interchangeable 13.long distance signal transmission 14.relative humidity and temperature measurement

Product Details:

100% brand new and high qualityBoard DS18B20 chip left 3P hole seat easily accessible DS18B20 chipOnboard power indicatorSpecificationWorking voltage:3.3V-5VWeight:4 gColor:- As shown in the pictureSize:- 21 (mm) x10 (mm)

Product Details:

This DS18B20 Temperature Sensor Module For Arduino, a Digital temperature sensor DS18B20 will tell you, with 9 to 12-bit resolution! Uses only 1 wire to the Arduino or other micro-controller for communication. With the One Wire protocol, you can operate a large number of these sensors from one Arduino pin.

This is the latest DS18B20 1-Wire digital temperature sensor from Maxim IC. Reports °C with 9 to 12-bit precision, -55°C to 125°C (+/-0.5°C). Each sensor has a unique 64-Bit Serial number etched into it allows for a huge number of sensors to be used on one data bus.

This is a wonderful part that is the cornerstone of many data-logging and temperature control projects.

Features :

1. Unique 1-Wire interface requires only one port pin for communication
2. Each device has a unique 64-bit serial code stored in an onboard ROM
3. Multidrop capability simplifies distributed temperature sensing applications
4. Requires no external components
5. Thermometer resolution is user-selectable from 9 to 12 bits
6. Converts temperature to the 12-bit digital word in 750ms (max.)
7. User-definable nonvolatile (NV) alarm settings
8. Alarm search command identifies and addresses devices whose temperature is outside of programmed limits (temperature alarm condition)
9. Applications include thermostatic controls, industrial systems, consumer products, thermometers, or any thermally sensitive system

Product Details:

• DS18B20 original chip,three wire temperature sensor
• High quality stainless steel tube encapsulation waterproof moisture proof prevent rust
• No other components, unique single bus interface
• 9 ~ 12 adjustable resolution
• Accuracy over the range of -10°C to 85°C: ±0.5°C.

Product Details:

This is XH-W1209 12V Digital Temperature Controller Module W/ Display and NTC Waterproof Temperature Sensor.

W1209 Mini thermostat Temperature controller is low-cost 12V Temperature controller with 7-segment display and 3 switch keypad for setting temperature and other parameters. The module features an NTC thermistor temperature sensing and has an accuracy of 0.1 C.

The XH-W1209 12V Digital Temperature Controller Module W/ Display and NTC Waterproof Temperature Sensor is an incredibly low cost yet highly functional thermostat controller. With this module, you can intelligently control power to most types of electrical device based on the temperature sensed by the included high accuracy NTC temperature sensor.

Although this module has an embedded microcontroller no programming knowledge is required. 3 tactile switches allow for configuring various parameters including on & off trigger temperatures. The onboard relay can switch up to a maximum of 240V AC at 5A or 14V DC at 10A. 

The current temperature is displayed in degrees Centigrade via its 3 digit seven segment display and the current relay state by an onboard LED.

Product Details:

Description:HTC-1 Digital Multi Monitoring system comes with Temperature thermometer, Humidity hygrometer,  Clock with Alarm on the large LCD display which shows Bold Digital figures.This Gadget is generally used for an incubator to monitor Real-time temperature and Humidity with daily Calendar, clock and alarm system on one single large LCD screen display, features one-inch tall digital numbers which can be seen from 50 feet away. It can also add an aesthetic look to your laboratory, work station, home or office.Three adjustment push of buttons are given along with max and min temperature readings, perfect for home or office, features an economical way to monitor indoor or outdoor temperature and humidity, measures temperatures as low as -58° Fahrenheit ( -50 c ) and up to +158° Fahrenheit ( 70ºc ), watch has both 12 24 hour format, display temperature, humidity & time simultaneously, memory of max-min humidity & temperature readings, large character LCD display, easy to read, lower power consumption.The Gadget has an option to switch the Unit of temperature between Celcius and Fahrenheit by just pressing a push-button given on the backside.
Specifications and Features:1. Large LCD display shows big Digital Numbers2. Temperature, Humidity and Time can be seen simultaneously.3. It has Stand to use as table-top or Hook for placing on the wall.4. Integral-hour alarm function5. Time, Date & Month display6. Low Power Consumption7. Adjustment Buttons to select Mode, Setup, and Memory.
Package Includes:1 x HTC-1 High Precision Large Screen Electronic Indoor Temperature, Humidity Thermometer with Clock Alarm.

Product Details:

Description:-
Feature:
-Mini temperature controller with socket.
-With clear digital display for better readability.
-Wide temperature measuring range.
-Directly power output.
-High Control precision 0.1 centigrade
-Can be used for domestic freezer, water tanks, refrigerator,industrial chiller, steamer, industrial
Key Operation Instruction:
P0 setting start temperature
Press the SET button to enter the internal menu. The default display is P0. Press the SET button again to set the desired starting temperature with the up and down buttons.
P1 setting stop temperature
Press the setting button to enter the internal menu, the digital display is P0, switch to P1 by the up and down buttons, press the setting button again, and set the required stop temperature by the up and down buttons.
P2 Setting calibration temperature
In the same way, enter the internal menu, switch to P2 by the up and down buttons, and then press the faint setting button. Set the required calibration temperature by the up and down buttons.
 P3 Setting starting delay time
In the same way, enter the internal menu, switch to P3 by pressing the up and down buttons, press the setting button again, and set the required delay time (in minutes) by the up and down buttons.

Specification :-
Temperature measure range:-50 110
Temperature control range:-50 110
Control accuracy:0.1
Measure input:NTC10K L=1 waterproof probe
Output:DC
Output colume:Max. 10A
Input voltage:110-220V
Model:XK-W2001
Digital display
Power:1500W
Measure Cable length:1M, 2M, 5M(Optional)

Product Includes:-
1x Temperature Controller

Product Details:

This digital humidity control controller is with wide humidity measuring range and controlling range, comes with a humidity controller sensor probe with cable. Humidity sensor uses a high-precision capacitive faster chip which has the advantage of high accuracy to refect. Humidity measuring range is 1% ~ 99% RH and control range is 1% RH. Humidification and dehumidification can be set through the menu, the parameters has been set the power outage permanent memory function. 
Specification : 
Humidity Measuring Range: 1%RH ~ 99% RH. Humidity Measuring Error: ±3%RH. Control Range: 1%RH. Display precision: 1% RH. Humidity Type: Capacitive. Power Suppler: AC220V±10%, 50/60Hz. Power consumption: ≤ 3W, Output Load: AC 10A/220V. Working temperature: 0°C - 80 °C. Size(L x W x H): Approx. 85 x 75 x 35mm / 3.4 x 3 x 1.4 inch. Probe Size (L x W): Approx. 60 x 15mm / 2.4 X 0.59 inch. Cable Length: Approx. 146cm / 57.5 inch. 
Functions : 
Function of humidification and dehumidification. Hysteresis function. Humidity correction. Delay protection. Function of Upper and Lower limit. 
Package Includes:
1 x Humidity controller. 1 x Humidity controller sensor probe with cable. 1 x Operation manual.

Product Details:

Get the all-new DC 12V XH-M452 Temperature And Humidity Controller Module Digital Display. It has a very High Accuracy Dual Output Automatic Constant Temperature And Humidity Control Board.Humidity Control1. Set to start humidity: long-press the + key, start the humidity value flashing, set by + / – key launch humidity value2. Set stop humidity: long press – to stop humidity value, set by + / – key to stop the humidity valueTemperature Control1. Setting the temperature +: Normal display mode, long-press the + key for 3 seconds, start temperature numerical flashing, press the + / – key setting values, the wrong operation after 5 seconds, automatically return to detect temperature display2. Setting the temperature – :Normal display mode, long press – button for 3 seconds, stop numerical flashing temperature, press the + / – key set value3. Restore the factory Settings: At the same time long press temperature, and humidity + key for 3 seconds, digital display, 888, 8884. Setting the start temperature: Long press the + key, start the flashing temperature, set start temperature by + / – key5. Setting Stop temperature: long press – button, stop flashing temperature, set stop temperature by + / – key
Features:1. Power supply: DC 12V2. Temperature measurement range:-40~120 3. Humidity range 0~100%RH4. Control precision 0.1  0.1%RH5. Test probe Integrated sensorPackage Includes:1 x XH-M452 Temperature and Humidity Controller Module With sensor

Product Details:

This is XH-W1219 12V Digital Red+Green Display Temperature Controller Module W/ NTC Waterproof Temperature Sensor. The XH-W1219 thermostat module with its STM8S µC and I/O (sensor input, keys, double display, relay) can be re-programmed for automation tasks, and it’s easy to work with.
Digital thermostat module. The temperature controller/switch with waterproof NTC probe and integrated LED display in red and green.
Specifications - Model - XH-W1219Control Range(°C) - -50 to +110Control Precision(°C) - 0.1Measuring Input - NTC10K SensorHigh-Temperature Alarm(°C) - -49 to +110Input Voltage (V) - 12Output Type - Relay Output 10A (max)Return Difference Setting(°C) - 0.1 to 30Delay Starting(min) - 0 to 10Temperature Calibration(°C) - -10 to 10
Button Functions :P0(Temperature Control Mode)»When first use this product; if you are using it for heating, please set H, if using it for cooling, please set C
P1(Return Difference Setting)»Long press SET key entering into the internal setting, choose P1 setting; then press SET key to achieve return difference value setting
P2(Temperature Calibration)»This function is for temperature calibration. If detection temperature and the actual temperature is different, then users can apply this function to calibrate
P3(Delay Start)»This function is for compressor cooling
P4(Set High-Temperature Alarm Value)»When the actual temperature is higher than this value, the screen will flash and sound an alarm

Product Details:

MH1210W 90-250V 10A 110V 220V Digital Temperature Thermostat Regulator Controller -50~110 Celsius Heat Cool Control NTC Sensor
Parameter:The working voltage is referenced on the product casing;Measurement error ± 0. 5°CTemperature control accuracy:    1°C  Display accuracy 0.1°CNTC25°C=10K B3435 Soil 1% (1 meter long, regardless of positive or negative)Power supply voltage: DC 9~72V/AC 90 -250V(Option)Working environment: Temperature: -20°C ~ 70°C, humidity: 90% RH no condensationProduct size: 75*85*35 (width, depth, height) mm Instruction:Press the S key for 3 seconds to enter the program menu code mode, which displays the code HC. Press the  or   key to cycle through the HC-CP-LA-PU-CA parameters. To enter a code, press the S key, press the  or  key to change the desired value and press SET to save and exit. . Control temperature setting: Short press S key (not more than 2 seconds) to display the factory default control temperature. Press  or  key to change the value well to save automatically. (Press and hold the  or  key for 2 seconds to quickly adjust the value.)

Product Details:

This is XH-W3001 AC 220V 1500W Digital Temperature Controller Microcomputer Thermostat Switch Module. A temperature measurement and Controller tool with high accuracy and precision at a very low cost.

It offers a high-temperature control precision of 0.1 The temperature control range from 50 to 110

The LED display shows the results clearly. One can directly install or embed the XH-W3001 in industrial control equipment panel, convenient and quick.

It features a 1M probe made up of stainless steel material which makes it waterproof and does not let it rust easily. Also, all the delicate and sensitive components are kept safe in ABS flame retardant housing which is avirulent and environmental protective.

Button functions:-• Press UP to show the start temperature button.• On Long press of the UP button, the display starts flashing, then press the UP or DOWN button Set the beginning of the temperature value• Press Down the display button to stop temperature.• On the Long press of the Down button, the display starts flashing, then press the Up or Down button Set to stop the temperature value.

Features of XH-W3001 220V AC 1500W Digital Temperature Controller Microcomputer Thermostat Switch Module:-• Easy to install• Output type: AC Output (AC 220V 1500W).• Output capacity: MAX 10A temperature measurement, display; refrigeration, heating control• Temperature setting upper and lower limits• Simple operation, suitable for seafood machines.• Upper key: The start temperature is displayed in one press, and long press to set start temperature.• Lower key: The stop temperature is displayed in one press, and long press to set stop temperature.

Product Details:

1 can detect ambient humidity and temperature2 sensor DHT113 humidity measuring range: 20%-95% (range 0-50 degrees) and humidity measurement error: +-5%4 temperature measurement range: 0-50 degree temperature measurement error: +-24 operating voltage 3.3V-5V5 output digital output6 fixed bolts holes, is easy to install7 small Board PCB dimensions: 3.2cm*1.4cm8 power led (red)  1 VCC add-ins 3.3V-5V2 GND external GND3 DO small-plate switch digital output interface connect monolithic integrated circuit IO mouth Package :
DHT11 DIGITAL RELATIVE HUMIDITY & TEMPERATURE SENSOR MODULE20cm DuPont line 3

Product Details:

Working Voltage Range: DC 4.5V- 20V
Current Drain: <60uA
Detection Range: <140°
Voltage Output: High/Low level
Signal: 3.3V TTL output
Detection Distance: 3 to 7m (can be adjusted)Delay
Time: 5 to 200s (Can be Adjusted, Default 5s +/- 3%)
Blockade time: 2.5s (Default)
Trigger: L: Non-repeatable trigger
H: Repeat Trigger (DefaultWork temperature: -20-+80°CTrigger
Method: L Unrepeatable Trigger / H Repeatable TriggerMaterial: Mixed Material
Dimension: 3.2cm x 2.4cm x 1.8cm (Approx)Sensitive
Setting: Turn to Right,

Product Details:

This DHT11 Temperature & Humidity Sensor features a temperature & humidity sensor complex with a calibrated digital signal output. By using the exclusive digital-signal-acquisition technique and temperature & humidity sensing technology, it ensures high reliability and excellent long-term stability. This sensor includes a resistive-type humidity measurement component and an NTC temperature measurement component, and connects to a high-performance 8-bit microcontroller, offering excellent quality, fast response, anti-interference ability and cost-effectiveness.

Product Details:

DHT22 output calibrated digital signal. It utilizes exclusive digital-signal-collecting-technique and humidity sensing technology, assuring its reliability and stability.Its sensing elements is connected with 8-bit single-chip computer.Every sensor of this model is temperature compensated and calibrated in accurate calibration chamber and the calibration-coefficient is saved in type of programme in OTP memory, when the sensor is detecting, it will cite coefficient from memory.Small size & low consumption & long transmission distance(20m) enable DHT22 to be suited in all kinds of harsh application occasions.

Product Details:

100mm Spade K-Type Temperature Controller Thermocouple Sensor -100°C to 1250°C Probe 2MProduct Description:- High measurement accuracy and medium interference free- Fast thermal response and sensitive to temperature variation- Wide measurement range- High performance and mechanical strength- Long use and easy installation- Works well with temperature controller(not included here)- Type: K Type, Spade type- Temperature Range: From -100°C to 1250°C- Probe Diameter: Approx.8mm / 0.31"- Probe material: Stainless Steel.- Cable Internal Insulation: Fiberglass- Cable External Shielding: Stainless Steel Braiding- Cable Total Length: Approx. 2M / 78.7"- Fork Terminal Spacing: Approx. 4mm / 0.15"