Modules - Relay

Product Details:

This is DC To AC SSR-40DA Solid State Relay Module 3-32VDC/24-380VAC 40A. A solid state relay (SSR) allows you to control high-current AC loads from lower voltage DC control circuitry. Solid state relays have several advantages over mechanical relays.

One such advantage is that they can be switched by a much lower voltage and at a much lower current than most mechanical relays. Also, because there are no moving contacts, solid state relays can be switched much faster and for much longer periods without wearing out.

This particular SSR can switch current loads of up to 40A with a 3-32V DC input and a zero cross trigger control method. Each one of these relays is equipped with four screw terminals (for use with ring or fork connectors) and a plastic cover that slides over the top of the relay to protect the terminals.

1. Model: SSR-25DA
2. Operating Voltage(VDC): 3-32
3. Operating Load Voltage (VAC): 24-380
4. Rated Load Current (A): 25
5. Color  Light Gray

Product Details:

This is DC To AC SSR-40DA Solid State Relay Module 3-32VDC/24-380VAC 40A. A solid state relay (SSR) allows you to control high-current AC loads from lower voltage DC control circuitry. Solid state relays have several advantages over mechanical relays.

One such advantage is that they can be switched by a much lower voltage and at a much lower current than most mechanical relays. Also, because there are no moving contacts, solid state relays can be switched much faster and for much longer periods without wearing out.

This particular SSR can switch current loads of up to 40A with a 3-32V DC input and a zero cross trigger control method. Each one of these relays is equipped with four screw terminals (for use with ring or fork connectors) and a plastic cover that slides over the top of the relay to protect the terminals.

Product Details:

This is DC To AC SSR-25DA Solid State Relay Module 3-32VDC/24-380VAC 25A. A solid state relay (SSR) allows you to control high-current AC loads from lower voltage DC control circuitry. Solid state relays have several advantages over mechanical relays.

One such advantage is that they can be switched by a much lower voltage and at a much lower current than most mechanical relays. Also, because there are no moving contacts, solid state relays can be switched much faster and for much longer periods without wearing out.

This particular SSR can switch current loads of up to 25A with a 3-32V DC input and a zero cross trigger control method. Each one of these relays is equipped with four screw terminals (for use with ring or fork connectors) and a plastic cover that slides over the top of the relay to protect the terminals.

Items: Solid State Relay.
Model: SSR-40 DD.
Input voltage: 3-32VDC.
Output voltage: 5-60VDC.
Output current: 40A.
On voltage: 1V.
One-off Time: 10ms.
Off leakage Current: 2mA.
Weight: 0.106kg.

Product Details:

This is a 5V and 12V 16 Channel Relay Module with Light Coupling LM2576 Power Supply, Be able to control various appliances and other equipment with a large current. It can be controlled directly by Micro-controller (Arduino, 8051, AVR, PIC, DSP, ARM, MSP430, TTL logic).

This is 5V and 12V 16-Channel Relay interface board and each one of the individual relays needs 15-20mA Driver Current. The board features indication LED for Relay output status and the standard interface that can be controlled directly by many of widely used microcontrollers like Arduino etc.

The 5V and 12V electromechanical relay module with AC contact capacity of 250V which also include light coupling protection(optocoupler) for isolation of control circuitry. The plate load power module doesn’t need an external power supply. It supports all SCM Drive.

The LM2596S buck chip in this relay module shows a slight fever which is a normal phenomenon as relays, long working hours have normal fever characteristics. 4 relay load power to give leave some margin, should avoid high-power (about 2000W) and long working environment, there will be some impact on the life of the product.

Additional Information:

• Item Code: RLY12V16LM

Product Details:

Available in below variants - 
1) Solid Relay Module 1 channel 5v low level trigger
2) Solid Relay Module 2 channel 5v low level trigger
3) Solid Relay Module 4 channel 5v low level trigger

Input section:

DC(+): Positive power supply (by relay voltage power supply). 

DC(-): Connect power negative. 

CH1: 1 relay module signal to trigger the end (high level trigger effective). 

Working current : 12.5mA. 

Trigger voltage : 3.3-5V. 

Trigger current : 2mA. 

Product Details:

4-channel relay output modules, relay output contacts 250A 10A. Input IN1, IN2, IN3, IN4, the signal line LOW effective. VCC, GND power input, can relay a separate power supply relay power input of JD-VCC.

Uses:

• Support all MCU control.
• The industrial sector
• PLC control
• Smart home control

Product Details:

Isolation groove between the control area and the load area Has the power and relay action instructions, pull bright, disconnect does not shineIf the input has signal, the beginning of the common and often will have conductionCan be used as a microcontroller development boardCan be used as a home appliance controlControl DC or AC signalsCan control AC 220V loadNormally open and normally closed contactsBlue KF301 terminal accesses control line is more convenient
Packing list: 1 x Module

Additional Information:

• Item Code: 1C12VRELAY

Product Details:

This is a 5V 2-Channel Relay interface board, Be able to control various appliances, and other equipments with large current. It can be controlled directly by Micro-controller (Arduino , 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic) .

5V and 12V 2-Channel Relay interface board, and each one needs 15-20mA Driver Current
Equiped with high-current relay, AC250V 10A ; DC30V 10A
Standard interface that can be controlled directly by microcontroller (Arduino , 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic)
Indication LED’s for Relay output status

Product Details:

Description:This is a 1 channel version of different relays available in our shop. The USB Control 1 Channel Module 5V Relay Module has the Onboard USB Control Module with one 5V Relay Module with a square USB port, and the connection is stable.It has a high-performance USB controlling chip and genuine relay on board as well as military-level PCB board workmanship. The USB Control 1 Channel Module 5V Relay Module supports Win7, XP 32 system. The module board has fully machinery processing. And all patch parts manufacturing and each module are tested OK before shipment for high reliability.
Features :1. The onboard square USB interface, stable connection.2. Use imported high-performance USB control chip.3. Application code: Green indicates that the  relay is in the closed state, the red disconnect4. Military-grade PCB board production.5. Use genuine pine music relay6. Support Windows 7, XP 32-bit systems
Package Includes :1×USB Control 1 Channel Module 5V Relay Module