Bombay Electronics
Bombay Electronics
Grant Road, Mumbai, Maharashtra
GST No. 27AABPC5348L1ZO
TrustSEAL Verified
Call 08048076458 50% Response Rate
SEND EMAIL

Arduino & Raspberry Pi Ecosystem

Complete range of Arduino boards and Raspberry Pi Boards along withperipherals. We have more products than the ones listed. Due to listing limitations we have only show cased few products.

Arduino Uno R3

Arduino Uno R3
  • Arduino Uno R3
Get Best Quote
Approx. Price: Rs 285 / UnitGet Latest Price

Product Details:

Minimum Order Quantity1 Unit
ProcessorATMEGA 328
BrandRobodo
Model NoR-3
Operating Voltage5V DC
Input Voltage9V DC
Alternate input voltage sourceUSB connection

Description -

Richduino is better option for students, trainers, faculties, professors, engineers, industries offer high quality affordable boards for Arduino IDE.
Richduino is inspired from open source Arduino platform specifications.
Low price and highest degree of production quality are two main objectives of Freeduino.

 

Technical specifications-

Microcontroller : Atmega328

Operating Voltage : 5V DC

Input Voltage (via DC Adapter) : 9V DC

Alternate input voltage source : USB connection

Digital I/O pins : 14 (of which 6 can be used as PWM output)

Analog input pins : 6 (with modification in code, these pins act as normal I/O pins)

DC Current Limit for I/O Pins : 40mA

DC Current Limit for 3.3V Pin : 500mA (if input voltage is sourced from DC adapter)

DC Current Limit for 3.3V Pin : 150mA (if input voltage is sourced from USB)

Switching between power sources : Manual Jumper Pin

Program Memory : 32KB onchip memory of ATmega328 (of which 0.5KB is used by bootloader)

SRAM : 2KB onchip memory of ATmega328

EEPROM : 1KB onchip memory of ATmega328

Clock Speed : 16Mhz

Mechanical Pin compatibility : with Arduino UNO R3

Board dimensions: 69mm X 55mm (Board is rectangular)

Mounting holes : Matching with UNO R3

Request
Callback
Yes! I am Interested

Arduino Nano Board R3 with CH340 chip without USB Cable compatible with Arduino (Unsoldered)

Arduino Nano Board R3 with CH340 chip without USB Cable compatible with Arduino (Unsoldered)
  • Arduino Nano Board R3 with CH340 chip without USB Cable compatible with Arduino (Unsoldered)
Get Best Quote
Approx. Price: Rs 180 / UnitGet Latest Price

Product Details:

Minimum Order Quantity1 Unit
Memory32 KB
ProcessorATmega328
Digital I/O PinDigital I/O Pins - 14 ; Analog I/O Pins - 8
ColorBlue
Frequency50 to 60 Hz
VoltageOperating Voltage(VDC) - 5 ; Input Voltage (V) - 7 to 12
Current RatingDC Current per I/O Pin - 40 mA

Description -

Richduino is better option for students, trainers, faculties, professors, engineers, industries offer high quality affordable boards for Arduino IDE. 
Richduino is inspired from open source Arduino platform specifications. 
Low price and highest degree of production quality are two main objectives of Freeduino. 

 

Technical specifications-

Microcontroller : Atmega328

Operating Voltage : 5V DC

Input Voltage (via DC Adapter) : 9V DC

Alternate input voltage source : USB connection

Digital I/O pins : 14 (of which 6 can be used as PWM output)

Analog input pins : 6 (with modification in code, these pins act as normal I/O pins)

DC Current Limit for I/O Pins : 40mA

DC Current Limit for 3.3V Pin : 500mA (if input voltage is sourced from DC adapter)

DC Current Limit for 3.3V Pin : 150mA (if input voltage is sourced from USB)

Switching between power sources : Manual Jumper Pin

Program Memory : 32KB onchip memory of ATmega328 (of which 0.5KB is used by bootloader)

SRAM : 2KB onchip memory of ATmega328

EEPROM : 1KB onchip memory of ATmega328

Clock Speed : 16Mhz

Mechanical Pin compatibility : with Arduino UNO R3

Board dimensions: 69mm X 55mm (Board is rectangular)

Mounting holes : Matching with UNO R3

Request
Callback
Yes! I am Interested

Arduino Mega 2560

Arduino Mega 2560
  • Arduino Mega 2560
Get Best Quote
Approx. Price: Rs 650 / UnitGet Latest Price

Product Details:

Minimum Order Quantity1 Unit
Memory256 KB of which 8 KB used by boot-loader.
ProcessorATmega2560
Digital I/O Pin54 (of which 15 provide PWM output)
Operating Voltage5V DC
Input Voltage9V DC
Alternate input voltage sourceUSB connection
Current Rating100-200 mA

Description -

Richduino is better option for students, trainers, faculties, professors, engineers, industries offer high quality affordable boards for Arduino IDE.
Richduino is inspired from open source Arduino platform specifications.
Low price and highest degree of production quality are two main objectives of Freeduino.

 

Technical specifications-

Microcontroller : Atmega328

Operating Voltage : 5V DC

Input Voltage (via DC Adapter) : 9V DC

Alternate input voltage source : USB connection

Digital I/O pins : 14 (of which 6 can be used as PWM output)

Analog input pins : 6 (with modification in code, these pins act as normal I/O pins)

DC Current Limit for I/O Pins : 40mA

DC Current Limit for 3.3V Pin : 500mA (if input voltage is sourced from DC adapter)

DC Current Limit for 3.3V Pin : 150mA (if input voltage is sourced from USB)

Switching between power sources : Manual Jumper Pin

Program Memory : 32KB onchip memory of ATmega328 (of which 0.5KB is used by bootloader)

SRAM : 2KB onchip memory of ATmega328

EEPROM : 1KB onchip memory of ATmega328

Clock Speed : 16Mhz

Mechanical Pin compatibility : with Arduino UNO R3

Board dimensions: 69mm X 55mm (Board is rectangular)

Mounting holes : Matching with UNO R3

Request
Callback
Yes! I am Interested

Arduino Pro Mini Board

Arduino Pro Mini Board
  • Arduino Pro Mini Board
Get Best Quote
Approx. Price: Rs 170 / UnitGet Latest Price

Product Details:

Minimum Order Quantity1 Unit
Part NumberPro Mini
ProcessorATmega328
Digital I/O PinDigital I/O Pins: 14,analog input port: A0 ~ A7.
Supply voltage5v
Current Rating100-200 mA
Product TypeMini Board
Clock Speed16MHz

The Arduino Pro Mini Is A Microcontroller Board Based On The Atmega168 (datasheet). It Has 14 Digital Input/output Pins (of Which 6 Can Be Used As Pwm Outputs), 8 Analog Inputs, An On-board Resonator, A Reset Button, And Holes For Mounting Pin Headers. A Six Pin Header Can Be Connected To An Ftdi Cable Or Sparkfun Breakout Board To Provide Usb Power And Communication To The Board.
The Arduino Pro Mini Is Intended For Semi-permanent Installation In Objects Or Exhibitions. The Board Comes Without Pre-mounted Headers, Allowing The Use Of Various Types Of Connectors Or Direct Soldering Of Wires. The Pin Layout Is Compatible With The Arduino Mini.
There Are Two Version Of The Pro Mini. One Runs At 3.3v And 8 Mhz, The Other At 5v And 16 Mhz.
Request
Callback
Yes! I am Interested

Engraving CNC Shield V3.0

Engraving CNC Shield V3.0
  • Engraving CNC Shield V3.0
Get Best Quote
Approx. Price: Rs 200 / UnitGet Latest Price

Product Details:

Minimum Order Quantity1 Unit
Model Name/NumberCNC Shield
Digital I/O PinPWM Spindle and direction pins
MaterialPlastic, Electronic Part
Model NoV3.0
Frequency50 Hz
Voltage12-36V DC
Axis4-Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pin
CompatibleArduino Boards

A simple Arduino CNC shield kit (Arduino Extension Board) with the following features:

Latest Arduino CNC Shield Version 3.10
GRBL 0.9 compatible. (Open source firmware that runs on an Arduino UNO that turns G-code commands into stepper signals)
PWM Spindle and direction pins
4-Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13)
2 x End stops for each axis (6 in total)
Coolant enable
Uses removable Pololu A4988 compatible stepper drivers. (A4988, DRV8825 and others) (Not Included)
Jumpers to set the Micro-Stepping for the stepper drivers. (Some drivers like the DRV8825 can do up to 1/32 micro-stepping )
Compact design.
Stepper Motors can be connected with 4 pin molex connectors or soldered in place.
Runs on 12-36V DC. (At the moment only the Pololu DRV8825 drivers can handle up to 36V so please consider the operation voltage when powering the board.)
Please note that this is an unassembled kit and needs soldering.
* * * Jumpers color may vary depending on the available stock.
NOT INCLUDED:

Arduino Uno
1-4 Pololu A4988 compatible stepper drivers
Request
Callback
Yes! I am Interested

Digispark ATTiny85 USB Development Board

Digispark ATTiny85 USB Development Board
  • Digispark ATTiny85 USB Development Board
Get Best Quote
Approx. Price: Rs 185 / PieceGet Latest Price

Product Details:

Minimum Order Quantity1 Piece
Part NumberATTINY85
USB 2.0 PortsBuilt-in USB (and serial debugging)
Voltage110 to 220 V
Weight50 gm
Frequency50 to 60 Hz
Current Rating100-200 mA

Product Description:
The ATtiny85 based mini development board is similar to the Arduino, but cheaper and smaller (of course a bit less powerful). With a whole host of shields to extend its functionality and the ability to use the familiar Arduino IDE, this board is a great way to jump into microcontroller electronics.Product Specs:
Support for the IDE 1.0+ (OSX / Win / Linux)Power via USB or External Source - 5v or 7-35v (automatic selection)On-board 500ma 5V RegulatorBuilt-in USB (and serial debugging)6 I / O Pins (2 are used for USB only if your gram actively communicates over USB, otherwise you can use all 6 even if you are gramming via USB)8k Flash Memory (about 6k after bootloader)I2C and SPI (vis USI)PWM on 3 pins (more possible with Software PWM)ADC on 4 pinsPower LED and Test / Status LED (on Pin0)
Request
Callback


Additional Information:

  • Item Code: ATTINY85V2
Yes! I am Interested

Wemos D1 R2 WIFI ESP8266 Arduino Shield

Wemos D1 R2 WIFI ESP8266 Arduino Shield
  • Wemos D1 R2 WIFI ESP8266 Arduino Shield
Get Best Quote
Approx. Price: Rs 495 / PieceGet Latest Price

Product Details:

Minimum Order Quantity1 Piece
ColorBlue
SizeApprox. 68x53x13mm/ 2.7x2.1x0.51inches
Voltage5V(maximum input voltage 24V)
Current1A
Input range0-3.3V
SupportOTA wireless upload

Description:
- Based on ESP-8266EX
- Arduino compatible, using IDE Arduino to program
- 11 x I/O pins
- 1 x ADC pin (input range 0-3.3V)
- Support OTA wireless upload
- Onboard 5V 1A Switching Power Supply (highest input voltage 24V)


Request
Callback


Additional Information:

  • Item Code: D1R2SH
Yes! I am Interested

Raspberry Pi 3 Model B

Raspberry Pi 3 Model B
  • Raspberry Pi 3 Model B
Get Best Quote
Approx. Price: Rs 3,009 / UnitGet Latest Price

Product Details:

Minimum Order Quantity1 Unit
Model Numberv3 - B
SoC ( system-on-chip )Broadcom BCM2837
CPU4 x ARM Cortex - A53 , 1.2GHz
GPUBroadcom VideoCore IV
RAM1GB LPDDR2 (900 MHz)
Networking10 / 100 Ethernet , 2.4GHz 802.11n WireLess
BluetoothBluetooth 4.1 Classic, Bluetooth Low Energy
StorageMicro SD
GPIO40-Pin Header , Populated
Other Miscellaneous PortsHDMI , 3.5 mm audio jack , USB 2.0 , Ethernet , Camera ( CSI ) , Display ( DSI )

1.2GHz quad-core Broadcom BCM2837 CPU with 1GB LPDDR2 RAM - VideoCore IV 3D graphics core - 40 pin GPIO extended pins - Micro SD slot - 10/100 BaseT Ethernet - Micro-USB power source 5V, 2A
Request
Callback


Additional Information:

  • Item Code: RSPBRP3B
Yes! I am Interested

Uno WiFi R3 AtMega328p NodeMSU ESP8266 32mb Memory USB-TTL CH340G Compatible for Arduino UNO

Uno WiFi R3 AtMega328p NodeMSU ESP8266 32mb Memory USB-TTL CH340G Compatible for Arduino UNO
  • Uno WiFi R3 AtMega328p NodeMSU ESP8266 32mb Memory USB-TTL CH340G Compatible for Arduino UNO
Get Best Quote
Approx. Price: Rs 750 / PieceGet Latest Price

Product Details:

Memory32mb
ProcessorATmega328IC
USB 2.0 PortsMicro USB
Digital I/O PinDigital I/O Pins: 14; Analog I/O Pins: 6.
Wifi ModuleESP8266
Voltage3.3 ~ 5
USB to serial converterCH340G
Wifi802.11 b/g/n 2.4 GHz

Uno+WiFi R3 AtMega328p+NodeMSU ESP8266 32mb Memory USB-TTL CH340G Compatible for Arduino UNO is full integration on one board: Uno R3 ATmega 328 and WiFi ESP8266 with memory 32Mb (MegaByte). All of the modules can work together or separately. And everyone has their own pinout headers.

The convenient solution for the development of new projects requiring Uno and WiFi. Via USB you can update sketches and firmware for ATmega328 and for ESP8266. For this onboard have the USB-serial converter CH340G.

It is a modernized version of the classic Arduino UNO R3 board. Full integration of a microcontroller ATmega328 and a Wi-Fi chip ESP8266 with 32 MB memory on one board. All modules can work together or individually. Each of the microcontrollers has led to connecting peripheral sensors and modules.

A convenient solution for developing new projects that require Wi-Fi. Through USB, you can update sketches and firmware for both ATmega328 and ESP8266. For this on board, there is a UART converter CH340G. The board has a DIP switch, which switches the modes of interaction of microcontrollers ATmegaa328 and esp8266.

Operations of this board are very simple. The board has DIP-switch, to connect the modules. For example, to USB and ATmega328, USB and ESP8266, ATmega328 and ESP8266.


QUICK OVERVIEW
  1. USB-TTL converter.
  2. Logic Level: 5V.
  3. Operating Supply Voltage: 5V.
  4. Digital I/O Pins: 14.
  5. Analog I/O Pins: 6.
Request
Callback
Yes! I am Interested

Due AT91SAM3X8E ARM Cortex-M3 Board, 84MHz, 512KB Board Compatible with Arduino

Due AT91SAM3X8E ARM Cortex-M3 Board, 84MHz, 512KB Board Compatible with Arduino
  • Due AT91SAM3X8E ARM Cortex-M3 Board, 84MHz, 512KB Board Compatible with Arduino
Get Best Quote
Approx. Price: Rs 1,200 / PieceGet Latest Price

Product Details:

Memory96KBytes of SRAM
ProcessorMicrocontroller: AT91SAM3X8E. A 32-bit core,that allows operations on 4 bytes wide data within a si
Digital I/O Pin54 (of which 12 provide PWM output)
Analog I/O PinsInput-12 /Output-2 (DAC)
Clock Speed84 MHz
DC Current per I/O Pin130 mA,DC Current for 3.3V Pin: 800 mA,DC Current for 5V Pin: 800 mA
Input Voltage(Recommended)7-12V
Flash Memory512 KB all available for the user applications

The Due is a microcontroller board based on the Atmel SAM3X8E ARM Cortex-M3 CPU. The Due Arduino AT91SAM3X8E ARM Cortex-M3 Board is the first Arduino board based on a 32-bit ARM core microcontroller. It has 54 digital input / output pins (of which 12 can be used as PWM outputs), 12 analog inputs, 4 UARTs (hardware serial ports), a 84 MHz clock, an USB OTG capable connection, 2 DAC (digital to analog), 2 TWI, a power jack, an SPI header, a JTAG header, a reset button and an erase button.

The board contains everything needed to support the microcontroller; simply connect it to a computer with a micro-USB cable or power it with an AC-to-DC adapter or battery to get started. The Due is compatible with all Arduino shields that work at 3.3V and are compliant with the 1.0 Arduino pinout.

The SAM3X has 512KB (2 blocks of 256KB) of flash memory for storing code. The bootloader is pre-burned in a factory from Atmel and is stored in a dedicated ROM memory. The available SRAM is 96KB in two contiguous banks of 64KB and 32KB. All the available memory (Flash, RAM, and ROM) can be accessed directly as a flat addressing space.

It is possible to erase the Flash memory of the SAM3X with the onboard erase button. This will remove the currently loaded sketch from the MCU. To erase, press and hold the Erase button for a few seconds while the board is powered.

QUICK OVERVIEW

 

  1. Microcontroller: AT91SAM3X8E
  2. Operating Voltage: 3.3V
  3. Input Voltage (recommended): 7-12V
  4. Input Voltage (limits): 6-16V
  5. Digital I/O Pins: 54 (of which 12 provide PWM output)
  6. Analog Input Pins: 12
  7. Analog Outputs Pins: 2 (DAC)
  8. A 32-bit core, that allows operations on 4 bytes wide data within a single CPU clock.
  9. CPU clock at 84Mhz
  10. 96KBytes of SRAM
Request
Callback
Yes! I am Interested

Mega WiFi R3 Atmega2560 NodeMCU ESP8266 32Mb Memory USB-TTL CH340G Compatible For Arduino Mega

Mega  WiFi R3 Atmega2560 NodeMCU ESP8266 32Mb Memory USB-TTL CH340G Compatible For Arduino Mega
  • Mega  WiFi R3 Atmega2560 NodeMCU ESP8266 32Mb Memory USB-TTL CH340G Compatible For Arduino Mega
Get Best Quote
Approx. Price: Rs 1,000 / PieceGet Latest Price

Product Details:

MicrocontrollerATmega2560
WifiEsp8266 IC,802.11 b/g/n 2.4 GHz
USB-TTL converterCH340G
Power Out5V-800mA
Power Input USB5V (500mA max.)
Digital and Analog I/O pinsDigital - 54,Analog - 16
Clock Speed16MHz

Mega +WiFi R3 Atmega2560+NodeMCU ESP8266 32Mb Memory USB-TTL CH340G Compatible For Arduino Mega is Full integration on one board Mega R3 ATmega2560 and WiFi ESP8266 with memory 32Mb.

All of the modules can work together or separately. And everyone has their own pinout headers. The convenient solution for the development of new projects requiring Uno and WiFi. Via USB you can update sketches and firmware for ATmega328 and for ESP8266.

It is a customized version of the classic ARDUINO MEGA R3 board. Full integration of Atmel ATmega2560 microcontroller and ESP8266 Wi-Fi IC, with 32 Mb (megabits) of flash memory, and CH340G USB-TTL converter on a single board! All components can be set up to work together or independently.

For this onboard have the USB-serial converter CH340G. Use this board is very simple. The board has DIP-switch, to connect the modules. For example, to USB and ATmeg2560, USB and ESP8266, ATmega2560 and ESP8266.

Request
Callback
Yes! I am Interested

ADK USB Host Shield Compatible with Arduino

ADK USB Host Shield Compatible with Arduino
  • ADK USB Host Shield Compatible with Arduino
Get Best Quote
Approx. Price: Rs 600 / UnitGet Latest Price

Product Details:

Minimum Order Quantity1 Unit
BrandRobodo
ColorBlue
FrequencyComplies with USB Specification Revision 2.0 (Full-Speed 12Mbps Peripheral,Full-/Low-Speed 12Mbps/1
Voltage5/3.3V
Supports devicesSupports HID devices,such as keyboards,mice,joysticks,etc.

Supports Google Android ADK, Android phone: G1, Nexus One, Nexus S, Motorola Droid X 2. (cellphone system: Android 2.3.4 tablet system: Android 3.1); compatible with official Arduino products: Arduino Uno 328 Arduino Diecimila/Duemilanove 328 Arduino Mega 2560 (recommended) Arduino Mega 1280. Realize USB HOST for Arduino
Request
Callback
Yes! I am Interested

16 x 02 Charater LCD Keypad Shield

16 x 02 Charater LCD Keypad Shield
  • 16 x 02 Charater LCD Keypad Shield
Get Best Quote
Approx. Price: Rs 200 / UnitGet Latest Price

Product Details:

Minimum Order Quantity1 Unit
Size16 x 02
Current Rating100-200 mA
BacklightBlue
CompatibleArduino Boards
Arduino Library4 Bit Arduino LCD Library

The LCD Keypad shield is developed for Arduino compatible boards, to provide a user-friendly interface that allows users to go through the menu, make selections etc. It consists of a 1602 white character blue backlight LCD. The keypad consists of 5 keys — select, up, right, down and left. To save the digital IO pins, the keypad interface uses only one ADC channel. The key value is read through a 5 stage voltage divider.
Request
Callback
Yes! I am Interested

L293D Motor Driver Shield

L293D Motor Driver Shield
  • L293D Motor Driver Shield
Get Best Quote
Approx. Price: Rs 190 / UnitGet Latest Price

Product Details:

Minimum Order Quantity1 Unit
BrandRobodo
Model NoL293D
Frequency50 to 60 Hz
Voltage12to36V
Current Rating100-200 mA

  • Features: A monolithic integrated, high voltage, high current, 4-channel driver
  • Using this chip you can use DC motors and power supplies of up to 36 V, so that some pretty big motors and the chip can supply a maximum current of 600mA per channel Also known as a type of H-Bridge, which is typically an electrical circuit that enables a voltage to be applied across a load in either direction to an output, e.g. motor.
Request
Callback
Yes! I am Interested

Nano I / O Expansion Shield

Nano I / O Expansion Shield
  • Nano I / O Expansion Shield
Get Best Quote
Approx. Price: Rs 225 / UnitGet Latest Price

Product Details:

Minimum Order Quantity1 Unit
Model Name/NumberNano Expansion Shield
BrandRobodo
Output Voltage3.3 V ( using AMS1117 )
ColorBlue
CompatibleArduino Nano

It is a dedicated Arduino I / O Expansion Boards designed for leads , you can easily use NANO . We use colored pin, easier wiring area definitions , Red 5V , Black GND , yellow I / O .
Request
Callback


Additional Information:

  • Item Code: ARNANOEX
Yes! I am Interested

Ethernet Shield W5100 Main Board

Ethernet Shield W5100 Main Board
  • Ethernet Shield W5100 Main Board
Get Best Quote
Approx. Price: Rs 460 / UnitGet Latest Price

Product Details:

Minimum Order Quantity1 Unit
Model NoW5100
Frequency50 to 60 Hz
Voltage110 to 220 V
Current Rating100-200 mA

As per the differentiated necessities and specifications of our patrons, we are indulged in manufacturing and supplying a broad array of Arduino Ethernet Shield W5100 Main Board. Available in diversified specifications as per the needs of our clients, these boards are widely popular among our clients. Moreover, these boards are delivered at clients end within specified time frame.

Features:

  • Enhanced design
  • Quality assured
  • high finish

With this Ethernet Shield, your Arduino board can be connected to internet. . It supports use of a web client application to use Arduino as a distributed network sensor. This shield is stackable by accepting prototype shields or any other boards with an Arduino compatible


Interface:

 

  • With this Ethernet Shield, your Arduino board can be used to connect to internet.
  • Can be used as server or client.
  • Directly plug puzzle board, no soldering required.
  • Controller: W5100.
  • This is the latest version of the Ethernet Shield.
  • This Arduino Ethernet Shield which is based on the Wiznet W5100 Ethernet Chip gives you an easy way to get your Arduino Online.
  • It is directly supported by Arduino official Ethernet Library.
  • It adds a micro-SD card slot, which can be used to store files for serving over the network.
  • It is compatible with the Arduino Duemilanove (168 or 328), Uno as well as Mega (1280/2560) and can be accessed using the SD library.
  • The Wiznet W5100 provides a network (IP) stack capable of both TCP and UDP.
  • It supports up to four simultaneous socket connections.
  • Use the Ethernet library to write sketches which connect to the internet using the shield.
Request
Callback
Yes! I am Interested

Data Logger Module Logging Recorder Shield

Data Logger Module Logging Recorder Shield
  • Data Logger Module Logging Recorder Shield
Get Best Quote
Approx. Price: Rs 250 / UnitGet Latest Price

Product Details:

Minimum Order Quantity1 Unit
BluetoothNA
Model Name/NumberData Logger module
BrandRobodo
Sd card interfaceSD card interface works with FAT16 or FAT32 formatted cards. 3.3v level shifter circuitry prevents d

Features
  • A dedicated and well-designed data logging shield for Arduino.
  • It is easy to assemble and customize, also equipped with extensive documentation and libraries.
  • SD card interface works with FAT16 or FAT32 formatted cards. 3.3v level shifter circuitry prevents damage to your SD card
  • Real time clock (RTC) keeps the time going even when the Arduino is unplugged. The battery backup lasts for years
  • Works with Arduino UNO, Duemilanove, Diecimila, Leonardo or ADK/Mega R3 or higher. ADK/Mega R2 or lower are not supported
  • Request
    Callback


    Additional Information:

    • Item Code: DTLGSHLD
    Yes! I am Interested

    Bluetooth XBee Shield

    Bluetooth XBee Shield
    • Bluetooth XBee Shield
    Get Best Quote
    Approx. Price: Rs 375 / UnitGet Latest Price

    Product Details:

    Minimum Order Quantity1 Unit
    ColorDeep Blue
    MaterialFR4
    Model Numberv03
    BrandFunduino

    This shield can achieve a simple two crunodal ZigBee network,achieve wireless communication between with Arduino ,and allows the with Arduino to wireless communicate over a modified ZigBee protocol using the popular XBee module.

    It is a fully Assembled shield without the XBee module. It works with all XBee modules including the Series 1 and Series 2.5, standard and Pro versions.
    • Stackable design, easy to plug into ARDUINO development board;
    • Coupled with Arduino Bluetooth Bee Bluetooth module, and other Bluetooth devices can communicate Wirelessly;
    • Coupled with xbee module, you can achieve two or more sets of communication between Arduino or Arduino and PC Communications.
    Request
    Callback


    Additional Information:

    • Item Code: BTXBSHLD
    Yes! I am Interested

    Sensor Expansion Shield

    Sensor Expansion Shield
    • Sensor Expansion Shield
    Get Best Quote
    Approx. Price: Rs 205 / UnitGet Latest Price

    Product Details:

    Minimum Order Quantity1 Unit
    BrandRobodo
    Input TypeDC
    Variantv4.0 & v5.0
    InterfaceIIC

    We can build electronics projects just as easy as piling bricks. and community have made the programming much easier than ever before. How about some elixir on hardware part? Maybe it is not yet convenient to make complex interfaces, but we can at least start from the most commonly used modules.   By using electronic bricks, you may connect compatible boards easily with various digital, analog and I2C/Uart interfaces. These the breadboard-less firm connection are prepared to extensive modules like poteniometers, sensors, relays, servos...even buttons , just plug and play.
    Request
    Callback


    Additional Information:

    • Item Code: SENEXPV5
    Yes! I am Interested

    Acrylic Case or Shell for Arduino Uno R3

    Acrylic Case or Shell for Arduino Uno R3
    • Acrylic Case or Shell for Arduino Uno R3
    Get Best Quote
    Approx. Price: Rs 90 / UnitGet Latest Price

    Product Details:

    Minimum Order Quantity1 Unit
    ModelR3
    Frequency50 to 60 Hz
    Voltage110 to 220 V
    Current Rating100-200 mA

    Clear Acrylic Box / Enclosure / Case / Shell for Arduino Uno R3 Board Module . Please Note: The UNO R3 module is not included.

    Request
    Callback


    Additional Information:

    • Item Code: ARCASEFF
    Yes! I am Interested

    16 Channel 12-bit PWM Servo Drive Shield Board

    16 Channel 12-bit PWM Servo Drive Shield Board
    • 16 Channel 12-bit PWM Servo Drive Shield Board
    Get Best Quote
    Approx. Price: Rs 605 / PieceGet Latest Price

    Product Details:

    Minimum Order Quantity1 Piece
    Channel16-Channel
    Voltage110 to 220 V
    Frequency50 to 60 Hz
    PhaseSingle Phase

    Descriptions: You want to make a cool robot, maybe a hexapod walker, or maybe just a piece of art with a lot of moving parts. Or maybe you want to drive a lot of LEDs with precise PWM output. Then you realize that your microcontroller has a limited number of PWM outputs! What now
    Using only two pins, control 16 free-running PWM outputs! You can even chain up 62 breakouts to control up to 992 PWM outputs
    • It's an i2c-controlled PWM driver with a built in clock. That means that, unlike the TLC5940 family, you do not need to continuously send it signal tying up your microcontroller, its completely free running!
    • It is 5V compliant, which means you can control it from a 3.3V microcontroller and still safely drive up to 6V outputs (this is good for when you want to control white or blue LEDs with 3.4+ forward voltages)
    • 6 address select pins so you can wire up to 62 of these on a single i2c bus, a total of 992 outputs - that's a lot of servos or LEDs
    • Adjustable frequency PWM up to about 1.6 KHz
    • 12-bit resolution for each output - for servos, that means about 4us resolution at 60Hz update rate
    • Configurable push-pull or open-drain output
    • Output enable pin to quickly disable all the outputs
    We wrapped up this lovely chip into a breakout board with a couple nice extras
    • Terminal block for power input (or you can use the 0.1" breakouts on the side)
    • Reverse polarity protection on the terminal block input
    • Green power-good LED
    • 3 pin connectors in groups of 4 so you can plug in 16 servos at once (Servo plugs are slightly wider than 0.1" so you can only stack 4 next to each other on 0.1" header
    • "Chain-able" design
    • A spot to place a big capacitor on the V+ line (in case you need it)
    • 330 ohm series resistors on all the output lines to protect them, and to make driving LEDs trivial
    • Solder jumpers for the 6 address select pins
    Package Included: 1 x New 16-Channel 12-bit PWM/Servo Driver -I2C PCA9685 For Arduino
    Request
    Callback


    Additional Information:

    • Item Code: 16CHPWM
    Yes! I am Interested

    BBC Micro Bit Pocket Sized MB80-US Single Board Computer

    BBC Micro Bit Pocket Sized MB80-US Single Board Computer
    • BBC Micro Bit Pocket Sized MB80-US Single Board Computer
    Get Best Quote
    Approx. Price: Rs 1,000 / PieceGet Latest Price

    The BBC Micro Bit is an open-source hardware ARM-based embedded system designed by the BBC for use in computer education. The BBC micro bit is a handheld, programmable micro-computer that can be used for all sorts of cool creations, from robots to musical instruments – the possibilities are endless.

    BBC Micro Bit Board was designed to encourage children to get actively involved in writing software for computers and building new things, rather than being consumers of media. It has been designed to work alongside other systems, such as the Raspberry Pi.

    It can be coded from any web browser in Blocks, Javascript, Python, Scratch and more; no software required. The device is described as half the size of a credit card and has an ARM Cortex-M0 processor, accelerometer and magnetometer sensors, Bluetooth and USB connectivity, a display consisting of 25 LEDs, two programmable buttons, and can be powered by either USB or an external battery pack. The device inputs and outputs are through five ring connectors that form part of a larger 25-pin edge connector.

    The micro bit has a website full of coding languages, lesson plans, tutorials, and fun ideas to help The micro bit is completely programmable. That means each of its LEDs can be individually programmed as can its buttons, inputs and outputs, accelerometer, magnetometer and Bluetooth Smart Technology.

    Features:
    1. A 5×5 LED matrix with 25 red LEDs to light up and can display animated patterns, scrolling text and alphanumeric characters
    2. Two programmable buttons. Use them as a games controller, or control music on a smartphone
    3. The on-board motion detector or 3-AXIS digital accelerometer that can detect movement e.g. shake, tilt or free-fall and use it to control motion activated games
    4. A built-in compass, a 3D magnetometer to sense which direction you’re facing and your movement in degrees and detect the presence of certain metals and magnets
    5. Bluetooth Smart Technology. Connect the micro: bit to another micro bit, devices, phones, tablets, cameras and other everyday objects
    6. Five Ring Input and Output (I/O) including power (PWR), ground (GND) and 3 x I/O. The Micro bit can read values from sensors and control things like motors or robots
    7. 20 pin edge connector: This allows the micro: bit to be connected to other devices such as Raspberry Pi, Arduino, Galileo and Kano through a standard connector
    8. Micro-USB controller: This is controlled by a separate processor and presents the Micro bit to a computer as a memory stick
    Request
    Callback
    Yes! I am Interested

    ESP13 Shield Board

    ESP13 Shield Board
    • ESP13 Shield Board
    Get Best Quote
    Approx. Price: Rs 899 / UnitGet Latest Price

    Product Details:

    Minimum Order Quantity1 Unit
    Current70 to 200 ( maximum ) mA,during standby less than 200 microAmpere
    Weight20 grams
    Application TypeEmbedded Solutions,Hobby,Domestic R&D
    AMC RequiredNo

    Features :

    • WiFi using industrial-grade ESP8266 chips, modules for ESP13 with metal shield , strong anti-interference ability;
    • Standard pin compatible with the Arduino Uno R3 , Mega 2560 , such as main control board, a voltage conversion chip is used to connect with the Arduino Uno , 3.3V and 5V compatible
    • A serial port using dual dial the code switch to control, makes the extension board can separate as Ar-duin Uno extended board is used, can also be used as ESP8266 extension plate
    • Real serial WiFi, the Ar-duin program without any configuration
    • WiFi based on the Web Server configuration parameters and serial port
    • Can be used as an independent ESP8266 development board, download the official firmware the AT command, Node MCU open-source firmware, etc;
    • Can be used as an independent Arduino Uno expansion board, pins all leads.
    Request
    Callback


    Additional Information:

    • Item Code: WIFISHLD
    Yes! I am Interested

    ARM STM32 Development Board

    ARM STM32 Development Board
    • ARM STM32 Development Board
    Get Best Quote
    Approx. Price: Rs 285 / UnitGet Latest Price

    Product Details:

    Minimum Order Quantity1 Unit
    ModelSTM32F103C8T6
    Work Frequency / Clock72 MHz
    Length x Width53 x 22 mm
    Connector TypeFemale/Jack
    Number of Pins40
    ApplicationPCB, R & D

    A very useful module that acts as a Minimum System Development Board Module For Arduino . On-board Mini USB interface, you can give the board power supply and USB communication .
    Request
    Callback


    Additional Information:

    • Item Code: ARMSTM32
    Yes! I am Interested

    3.5 inch Touch Screen LCD Raspberry Pi

    3.5 inch Touch Screen LCD Raspberry Pi
    • 3.5 inch Touch Screen LCD Raspberry Pi
    Get Best Quote
    Approx. Price: Rs 1,300 / UnitGet Latest Price

    Product Details:

    BrandBombay Electronics
    InterfaceSPI
    BacklightYes,LED
    LCD TypeTFT
    Touch Screen TypeResistive Screen
    Touch ControllerXPT2046
    Colors65536
    Resolution (Pixel)320*480
    Aspect Ratio8:5

    This small 3.5-inch touch screen module is designed especially for Raspberry Pi, using the latest Linux Core system. This is ideal for DIY anywhere, anytime and does not require any separate power source or case to hold it. The module sits right on top of Pi and an ideal alternative solution for HDMI monitors. The screen also comes with a stylus to interact with the small screen.

    Note:
    1. To use the LCD with the Raspberry Pi official image, you need drivers. If you are not sure about the drivers, contact us
    2. Make sure the hardware connection is correct and connects fine if something seems not right
    3. It is strongly recommended to use a stand-alone 5V/2A power adapter, because the PC’s USB port may have not enough power to support both Pi and LCD
    Features:
    1. Designed for Raspberry Pi, an ideal alternative solution for HDMI monitor
    2. Supports all revision of Raspberry Pi (directly-pluggable models)
    3. Works with Raspbian/Ubuntu directly
    4. Comes with full set of screws and nuts for assembly
    5. 320×480 resolution, better display
    6. Lightweight and easy to install
    Package Includes:

    1 x 3.5″ Touch-Screen LCD Raspberry Pi
    1 x Touch Screen Stylus

    Request
    Callback
    Yes! I am Interested

    3.2 Inch TFT LCD Touch Screen Display V4.0 for Raspberry Pi

    3.2 Inch TFT LCD Touch Screen Display V4.0 for Raspberry Pi
    • 3.2 Inch TFT LCD Touch Screen Display V4.0 for Raspberry Pi
    Get Best Quote
    Approx. Price: Rs 1,200 / UnitGet Latest Price

    Product Details:

    Display TypeLED
    Size3.2 Inch
    Screen Type3.2 inch TFT Resistive
    Voltage5v
    Maximum Pixel Frequency320 x 240
    Touch PanelYes

    QUICK OVERVIEW
    1. Version: V4.0
    2. Resistive touch.
    3. Dimension: 3.2 inch.
    4. Operating Voltage: DC 5V.
    5. Driver: XPT2046.
    6. Resolution: 240 x 320.
    Request
    Callback


    Additional Information:

    • Item Code: RW320240
    Yes! I am Interested

    Raspberry PI Camera Module V2 - 8 Megapixel 1080p

    Raspberry PI Camera Module V2 - 8 Megapixel 1080p
    • Raspberry PI Camera Module V2 - 8 Megapixel 1080p
    Get Best Quote
    Approx. Price: Rs 2,596 / PieceGet Latest Price

    Product Details:

    Minimum Order Quantity1 Piece
    TypePI Camera Module
    Pixel3280x2464
    Video Resolution1080p30,720p60 and 640x480p90 resolutions
    SoftwareAll software is supported within the latest version of Raspbian Operating System
    SupportSupports Raspberry Pi 1,2,3 and 4
    ApplicationsCCTV security camera,motion detection,time lapse photography

    This 8mp camera module is capable of 1080p video and still images and connects directly to your Raspberry Pi. Connect the included ribbon cable to the CSI (Camera Serial Interface) port on your Raspberry Pi, boot up the latest version of Raspbian and you are good to go! The board itself is tiny, at around 25mm x 20mm x 9mm and weighing in at just over 3g, making it perfect for mobile or other applications where size and weight are important. The sensor has a native resolution of 5 megapixel, and has a fixed focus lens onboard. In terms of still images, the camera is capable of 2592 x 1944 pixel static images, and also supports 1080p30, 720p60 and 640x480p60/90 video. Note: This module is only capable of taking pictures and video, not sound. 
    Parameters: Lens: 1/4 5M Aperture: 2.9 Focal Length: 3.29 FOV: 72.4 degrees Hardware connection: 1 soft cable, 90-degree vertical connector, HDMI port next to it. 
    When connecting the contact side facing the HDMI interface. Before 2. tear protective film on the lens 3 bare boards, pay attention to ESD damage, beware of static electricity! 
    Software: 1. RPi firmware and raspi-config has been updated to the camera, do a apt-get update; apt-get upgrade; 2. raspi-config, select the camera, start RPi firmware camera driver, and then restart 3. using the command-line program raspivid and raspistill operate camera to capture video clips or images 4. to capture video clips need to play with mplayer How will the data through the network camera live broadcast out: By nc command (ncat - Concatenate and redirect sockets) of the input data of the camera, directly to the output ports of the network redirection.
    Request
    Callback


    Additional Information:

    • Item Code: RPI8MP
    Yes! I am Interested

    Raspberry Pi Zero-W V1.1 Development Board With Official Case

    Raspberry Pi Zero-W V1.1 Development Board With Official Case
    • Raspberry Pi Zero-W V1.1 Development Board With Official Case
    Get Best Quote
    Approx. Price: Rs 1,200 / PieceGet Latest Price

    Product Details:

    Memory512 MB
    ProcessorBCM 2835 SOC
    USB 2.0 PortsMicro-USB for Power Micro-CSI Camera Port,Micro-USB OTG Host for Data,Mini-HDMI for Video
    BluetoothWiFi + Bluetooth 4.1 + BLE (Bluetooth Low Energy).
    Clock Speed1GHz
    Operating Power5V DC @ 140mA

    QUICK OVERVIEW
    1. Processor: BCM 2835 SOC
    2. Clock speed: 1GHz
    3. RAM: 512MB
    4. Built-in Wireless: WiFi + Bluetooth 4.1 + BLE (Bluetooth Low Energy).
    5. Display and Audio: mini-HDMI
    6. USB Port: micro-B USB for data
    7. Power input: micro-B USB for power
    Request
    Callback
    Yes! I am Interested

    Raspberry Pi 4 Model-B with 2 GB RAM

    Raspberry Pi 4 Model-B with 2 GB RAM
    • Raspberry Pi 4 Model-B with 2 GB RAM
    Get Best Quote
    Approx. Price: Rs 3,200 / PieceGet Latest Price

    Product Details:

    Memory2GB LPDDR4 SDRAM
    ProcessorBroadcom BCM2711,quad-core Cortex-A72 (ARM v8) 64-bit SoC @ 1.5GHz
    USB 2.0 Ports2 x USB 2.0 Ports,2 x USB 3.0 Ports
    BluetoothBluetooth 5.0
    Graphics GPUH.264 (1080p60 decode,1080p30 encode); H.265 (4Kp60 decode); OpenGL ES,3.0 Graphics
    EthernetBLE Gigabit Ethernet
    WLAN802.11 b/g/n/ac (2,4 + 5,0 GHz)
    Processor Part NumberBroadcom BCM2711,quad-core Cortex-A72 (ARM v8) 64-bit SoC @ 1.5GHz
    Digital I/O PinStandard 40-pin GPIO Header

    Raspberry Pi 4 Model B is the latest product in the popular Raspberry Pi range of computers. It offers ground-breaking increases in processor speed, multimedia performance, memory, and connectivity compared to the prior-generation Raspberry Pi 3 Model B+

    What’s New in Raspberry Pi 4 B?

    1. 1GB/2GB/4GB Varients
    2. Quad-Core 64-bit Broadcom 2711, Cortex A72  Processor
    3. WLAN 802.11 b/g/n/ac (2,4 + 5,0 GHz)
    4. LAN RJ45 10/100/1000 Mbit (Gigabit LAN over USB 3.0)
    5. Operating Power 5V@3A  via USB Type-C Port
    6. Dual-Display Micro HDMI Ports which supports H 265 Decode for 4K Video @60p
    Request
    Callback
    Yes! I am Interested

    Raspberry Pi 4 Model-B with 4 GB RAM

    Raspberry Pi 4 Model-B with 4 GB RAM
    • Raspberry Pi 4 Model-B with 4 GB RAM
    Get Best Quote
    Approx. Price: Rs 4,000 / PieceGet Latest Price

    Product Details:

    Memory4GB LPDDR4 SDRAM
    ProcessorBroadcom BCM2711,quad-core Cortex-A72 (ARM v8) 64-bit SoC @ 1.5GHz
    USB 2.0 Ports2 x USB 2.0 Ports 2 x USB 3.0 Ports
    BluetoothBluetooth 5.0
    No. Of Coresquad-core Cortex-A72 (ARM v8) 64-bit SoC @ 1.5GHz
    EthernetBLE Gigabit Ethernet
    Digital I/O PinStandard 40-pin GPIO Header

    QUICK OVERVIEW
    1. 1GB/2GB/4GB Varients
    2. Quad-Core 64-bit Broadcom 2711, Cortex A72  Processor
    3. WLAN 802.11 b/g/n/ac (2,4 + 5,0 GHz)
    4. LAN RJ45 10/100/1000 Mbit (Gigabit LAN over USB 3.0)
    5. Operating Power 5V@3A  via USB Type-C Port
    6. Dual-Display Micro HDMI Ports which supports H 265 Decode for 4K Video @60p
      Request
      Callback
      Yes! I am Interested

      5MP Raspberry Pi Zero W Camera Module W/ HBV FFC Cable

      5MP Raspberry Pi Zero W Camera Module W/ HBV FFC Cable
      • 5MP Raspberry Pi Zero W Camera Module W/ HBV FFC Cable
      Get Best Quote
      Approx. Price: Rs 380 / PieceGet Latest Price

      Product Details:

      Pixel5MP
      Lens FocusFixed Focus
      Image Size(Pixels)2592x1944
      Interface TypeCSI(Camera Serial Interface)
      SensorsOmnivision 5647 fixed-focus
      Dimensions25x23x8 (LxWxH) mm

      The Raspberry Pi camera module can be used to take high-definition video, as well as stills photographs. It’s easy to use for beginners, but has plenty to offer advanced users if you’re looking to expand your knowledge. There are lots of examples online of people using it for time-lapse, slow-motion and other video cleverness. You can also use the libraries we bundle with the camera to create effects.

       

       

      • Small board size: 25mm x 20mm x 9mm
      • A 5MP (2592×1944 pixels) Omnivision 5647 sensor in a fixed focus module
      • Support 1080p30, 720p60 and 640x480p60/90 video record
      Request
      Callback
      Yes! I am Interested

      Raspberry PI Case Enclosure

      Raspberry PI Case Enclosure
      • Raspberry PI Case Enclosure
      Get Best Quote
      Approx. Price: Rs 200 / PieceGet Latest Price

      Product Details:

      Minimum Order Quantity1 Piece
      BrandRobodo
      ColorAvailable in transparent,red,black
      CompatibleAvailable for Complete RPI Range.
      Dimensions97mm x 70mm x 25mm / 3.8" x 2.8" x 1.0"
      Weight46g

      High-quality ABS constructionRemovable side panels and lid for easy access to GPIO, camera and display connectorsLight pipes for power and activity LEDsExtraordinarily Aesthetic
      Request
      Callback


      Additional Information:

      • Item Code: RPCS0209
      Yes! I am Interested

      Raspberry PI HDMI 5 Inch LCD Monitor With Touchscreen 800x480

      Raspberry PI HDMI  5 Inch LCD Monitor With Touchscreen 800x480
      • Raspberry PI HDMI  5 Inch LCD Monitor With Touchscreen 800x480
      Get Best Quote
      Approx. Price: Rs 2,600 / UnitGet Latest Price

      Product Details:

      Display TypeLED
      Size5 Inch
      Screen TypeCompatible with Raspberry Pi - TFT
      Touch PanelYes
      Resolution800x480

      This fantastic 5 inch HDMI LCD display with USB touch screen is compatible with almost all the operating systems on the market. Utilizing pre-existing Linux/Windows/Mac drivers, this 800 x 480 touch screen will help you hit the ground running. Resistive touch function gives the user full control over any device. It supports Windows XP SP3, Windows 7, Windows 8, Windows 8.1, Windows 10, Android 4.2, Windows CE7, Ubuntu and Debian. With the built-in EDID device information, your equipment will get identified in no time. Meanwhile, its USB touch can fulfill the functions of the right mouse button and drag and drop.

      With the special design power circuit for this display, it requires less than 150mA current to get it running with perfect performance. When you do not need the touch screen function, all you need is to plug a HDMI line to get it work. We have successfully run the tests on PC, laptop, Raspberry Pi, Beaglebone Black, Udoo, Compute stick, SLR camera.

      Specifications:

      Power:5V Power via USB Micro

      Current: less than 150mA

      Display Type:5 inch TFT LCD

      Resolution: 800x480

      Touchscreen: USB Resistive

      Interface: HDMI & USB 2.0 Full Speed

      Dimensions: 133mm x 76mm x 7mm 

      Weight without package:120g

      Weight with package:140g

      Features:

      USB Resistive Touch Control

      Plug and Play! No Driver Needed!

      Compatible with Raspbian, Ubuntu Mate, NOOBS with Raspberry Pi

      Compatible with Debian, Angstrom with BeagleBone Black

      Compatible with Windows/Ubuntu/Mac with PC

      Intel-Processor Base MiniPC Supports

      Ultra Low Power Consumption Backlight

      Request
      Callback


      Additional Information:

      • Item Code: RD800480
      Yes! I am Interested

      Mini Portable 2.4GHz Wireless Keyboard

      Mini Portable 2.4GHz Wireless Keyboard
      • Mini Portable 2.4GHz Wireless Keyboard
      Get Best Quote
      Approx. Price: Rs 767 / PieceGet Latest Price

      Product Details:

      Minimum Order Quantity1 Piece
      Operating range15 meters (MAX)
      Frequency range2.403GHZ-2.480GHZ
      Operational voltage3.3V
      Packaging TypeBox

      3 in 1 MultiFunction 2.4GHz Mini Wireless QWERTY keyboard, TouchPad combo,LED backlit with USB interface adapter.Perfect combo: 92 keys Wireless QWERTY Keyboard + Touchpad which supports multi-finger functions, A single finger click as left mouse function, two-finger click as the right mouse function, double finger drag as the rolling screenThis is a wonderful combo, 2.4GHz Mini Wireless QWERTY keyboard, TouchPad combo, New increased Backlit LED with USB interface adapter.Built-in high sensitive smart touchpad with 360-degree flip design.Ideal for devices such as PC, Mac, Xbox 360, Xbox One, PS3, PS4, Google Android TV Box, HTPC, IPTV
      Features:92 keys, 2.4GHz wireless Keyboard with Touchpad. Touchpad DPI adjustable functions. Built-in high sensitive smart touchpad with 360-degree flip design. Increased LED backlit function, you can us the keyboard in the dark with LED lighting QWERTY keyboard with multimedia control keys and PC gaming control keys. Auto sleep and auto wake mode. The Ergonomically handheld design is easy to carry and operate. Build-in removable rechargeable Li-ion battery that has longer standby time.
      Technical Specification: Operating range: 15 meters (MAX), without signal disturbance and no direction limit.Frequency range: 2.403GHZ 2.480GHZOperational voltage: 3.3VCharge Voltage: 4.4V 5.25VModulation: GFSK Layout : US Channel: 78 channels TX Power: less than +5dBmTransmission rate: 1M bit/sec Frequency tolerance: +/-30ppmPower consumption: 55mA(on), 1mA(sleep)Battery Type: Built-in lithium-ion battery
      Notice: After 3 minutes without any operating, the keyboard will go into sleep mode, press any key for about 1s to wake up keyboard.
      Package:1 Wireless keyboard1 Wireless receiver1 Charging data cable1 User manual
      Note: Your device need USB 2.0 jack to operate.
      Request
      Callback


      Additional Information:

      • Item Code: WLMKB00
      Yes! I am Interested

      Prototyping Shield with Mini BreadBoard

      Prototyping Shield with Mini BreadBoard
      • Prototyping Shield with Mini BreadBoard
      Get Best Quote
      Approx. Price: Rs 143 / UnitGet Latest Price

      Product Description:

      • Small soldering area.
      • All Arduino pins are brought to the top level.
      • 1 reset button, 1 general use button, and 2 LED circuits can be used directly.
      • 5V, GND, and Raw pins are exposed as well.
      • SOIC place for IC.
      • The mini breadboard has 170 tie points.
      • The breadboard sticks on the prototype shield with its self-adhesive backing.
      • Prototype Size:7cm x 5.5cm x 2cm
      • Mini breadboard size: 4.4 * 3.4 * 1cm
      Request
      Callback


      Additional Information:

      • Item Code: PRTPSHLD
      • Minimum Order Quantity: 1 Unit
      Yes! I am Interested

      Touch Screen - 7.0 inch for Raspberry Pi

      Touch Screen - 7.0 inch for Raspberry Pi
      • Touch Screen - 7.0 inch for Raspberry Pi
      Get Best Quote
      Approx. Price: Rs 3,600 / UnitGet Latest Price

      Product Details:

      Minimum Order Quantity1 Unit
      ConditionNew
      Screen SizeLess than 15 inches

      Features:

      800*480 (Pixel), IPS screen; Full view;
      Compatible with Raspberry Pi 3 Model B/ 2B/ B+ (Provide full image or separate driver);
      For Raspberry Pi, you can run Raspbian and Ubuntu(only provide the image for Pi 3B/2B);
      Compatible with Beagle Bone Black and Banana Pi/Pro;(Provide a full image)
      USB touch and HDMI display don''t occupy any GPIO;
      Support win7/win8/win10, No driver;
      No driver if you use Raspbian system, only add the following line setting in config.txt;

      max_usb_current=1
      hdmi_group=2
      hdmi_mode=1
      hdmi_mode=87
      hdmi_cvt 800 480 60 6 0 0 0

      Packing List:

      1 x Capacities touch screen
      1 x HDMI Cable (cable length: 21.5cm)
      1 x USB Cable (cable length: 35.5cm)
      Request
      Callback


      Additional Information:

      • Item Code: R7800480
      • Port of Dispatch: Mumbai
      Yes! I am Interested

      Pixy2 CMUcam5 Smart Vision Sensor - Object Tracking Camera

      Pixy2 CMUcam5 Smart Vision Sensor - Object Tracking Camera
      • Pixy2 CMUcam5 Smart Vision Sensor - Object Tracking Camera
      Get Best Quote
      Approx. Price: Rs 5,800 / PieceGet Latest Price

      The Pixy2 cam is an advanced camera with its own processor. This is an amazing sensor for making line following industrial grade robots alongwith color recognition and object recognition facilities. This is also compatible with Arduino and Raspberry Pi with available libraries. The cable for connecting to Arduino and Raspberry Pi Boards is provided with the Pixy2. The Pixy 2 is highly accurate and fast can enable your robots to follow lines of all thicknesses and even as thin as 3 mm at high speeds!!

      Pixy2 is the second version of Pixy. It''s faster, smaller and more capable than the original Pixy, adding line tracking/following algorithms as well as other features. With the added functionality of line detection, intersection detection and small barcodes, this make the job much simpler and robots much more accurate.

      The integrated light source of Pixy2 provides and added benefit while line following or following colour based objects.

      And of course, Pixy2 does everything that the original Pixy can do. Like its predecessor, the Pixy2 can learn to detect objects that you teach it, just by pressing a button. With these new algorithms, you can detect intersections and “road signs” as well. The Pixy2 has several interfaces including SPI, I2C, UART, and USB with simple communications, so you get your chosen controller talking to the Pixy2 in short order.

      The Pixy2 uses a color-based filtering algorithm to detect objects. Color-based filtering methods are popular because they are fast, efficient, and relatively robust. Pixy2 calculates hue and saturation of each RGB pixel from the image sensor and uses these as the primary filtering parameter

      Features:

      • Pixy2 detects lines, intersections and small barcodes, intended for line-following robots
      • Improved framerate: 60 frames/second
      • Tracking algorithms have been added to color-based object detection
      • Improved and simplified libraries for Arduino, Raspberry Pi and other controllers
      • Integrated light source
      • Small, fast, easy-to-use, low-cost, readily-available vision system
      • Connects to Arduino with included cable. Also works with Raspberry Pi, BeagleBone and similar controllers
      • Communicates via one of several interfaces: SPI, I2C, UART, USB or analog/digital output
      • C/C++ and Python are supported
      • Configuration utility runs on Windows, MacOS and Linux
      • All software/firmware is open-source GNU-licensed 

      Specifications:

      • Image sensor: Aptina MT9M114, 1296×976 resolution with integrated image flow processor
      • Processor: NXP LPC4330, 204 MHz, dual core
      • Lens field-of-view: 60 degrees horizontal, 40 degrees vertical
      • Power consumption: 140 mA typical
      • Power input: USB input (5V) or unregulated input (6V to 10V)
      • RAM: 264K bytes
      • Flash: 2M bytes
      • Available data outputs: UART serial, SPI, I2C, USB, digital, analog
      • Integrated light source, approximately 20 lumens

      Request
      Callback
      Yes! I am Interested
      X

      Explore More Product



      Reach Us
      Sahib Chandock (Sales Head)
      Bombay Electronics
      13- B Shamrao Vithal Marg, Off Lamington Road
      Grant Road, Mumbai - 400007, Maharashtra, India


      Call Us


      Send E-mailSend SMS